Кондиционеры Daikin UATYQ-CY1 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
32
STEP 7
-
Connect Belimo actuator, LF24-SR (item 1) with label ‘RA’, which is now located at the assembly damper on the
front panel to terminal block with label ‘RA’ inside the junction box.
-
There are four wires on the actuator with diff erent colours (black, red, green and white colours). Connect the
wires as below:
CAUTION
Wrong wiring connection may cause the malfunction on actuator or economizer controller board or both. Tie the wires
with releasable cable ties under the junction box.
Black colour wire - connect to fi rst pole of
terminal block with label ‘GND’.
Red colour wire
- connect to second pole of
terminal block with label
‘+24V’.
Green colour wire - connect to third pole of
terminal block with label ‘DCV’.
White colour wire - connect to fourth pole of
terminal block with label ‘FB’.
(You may refer to sticker wiring diagram which is
located on the front cover of junction box.)
Sticker wiring
diagram on
the front cover
of junction
box
-
Then, connect Belimo actuator, LF24-SR (item 1) with label ‘OA’, which is now located at the assembly damper
on the side panel to terminal block with label ‘OA’ inside the same junction box. Follow the same method used
for wiring connection between actuator ‘RA’ and terminal block ‘RA’. Next, attach the side panel to the unit. You
may need to do proper arrangement on the actuator wires by using cable ties (fi eld supply) before attach the
side panel to the unit.
Side panel in standard
unit which is removed in
step 5.
Side panel comes with
economizer kit which is
assembled with actuator in step
6. Attach this panel to the unit.
Junction
box
Terminal
block with
label ‘RA’
- to be
connected
with
actuator
with label
‘RA’.
Label ‘RA’
Label ‘OA’
Terminal block with label ‘OA’ - to be
connected with actuator with label ‘OA’.
Detail view of junction box
STEP 8
-
To build the rain hood, install the loose parts (metal parts) to the side panel. Before that, place the gasket (fi eld
supply) on the side panel for sealing purpose.
-
Then, follow the installation sequence below to build the rain hood:
Item 2
Item 6
Item 7
Item 3
Item 4
Item 5
Item 9
Item 8
Sealant
Gasket
TO PCB3 (ECO)
CN_ACT_RA
TO PCB3 (ECO)
CN_ACT_OA
TO PCB3 (ECO)
CN_C02
TB RA
TB OA
TB C02
BLA
CK
RED
GREEN
WHITE
BLA
CK
RED
GREEN
WHITE
BLA
CK
RED
WHITE
GND +24V DCV
FB
GND +24V DCV
FB
GND +24V
FB
ACTUATOR RA
ACTUATOR OA
C02 SENSOR
Side panel with outdoor
air damper (item 2) which
is assembled to the unit
in step 7.
Item 3
Item 7
Item 4
Item 5
Item 9
Item 8
Item 6
-
It is recommended to seal off all the joints and gaps with weather-proof sealant (such as silicone, fi eld supplied
item) in order to ensure a water-proof fi nishing on the rain hood.
1 IM 5RTBR-0710(2)-EN.indd 32
1 IM 5RTBR-0710(2)-EN.indd 32
1/10/11 3:39:16 PM
1/10/11 3:39:16 PM
