Обогреватели Master B 70CED 4011.819 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
5
GB
kerosene to tank,stir, and drain again. This will prevent excess
debris from clogging
fi
lters during future use.
4. Replace fuel cap or drain plug. Properly dispose of old and
dirty fuel. Check with local automotive service stations that
recycle oil.
5. If storing, store heater in dry place. Make sure storage place
is free of dust and corrosive fumes.
IMPORTANT:
Do not store kerosene over summer months for
use during next heating season. Using old fuel could damage
heater.
PREVENTATIVE MAINTENANCE SCHEDULE
WARNING: Never service heater while it is plugged in, operating, or hot. Severe
burns and electrical shock can occur.
Item
How Often
How To
Fuel tank
Flush every 150-200 hours of operation or as
needed
See
Storing, Transporting,or Shipping.
Air output andlint
fi
lters
Replace every 500 hours of operation or once a
year
See
Air Output, Air Intake, and Lint Filters
, page
7
Air intake
fi
lter
Wash and dry with soap and water every 500
hours of operation or as needed
See
Air Output, Air Intake, and Lint Filters
, page
7
Fuel
fi
lter
Clean twice a heating season or as needed
See
Fuel Filter
, page 6
Spark plug
Clean and regap every 600 hours operation
orreplace as needed
See Spark plug, page 6
Fan blades
Clean every season or as needed
See
Fan
, page 9
Motor
Not required/permanently lubricated
TROUBLESHOOTING
WARNING: Never service heater while it is plugged in, operating, or hot. Severe
burns and electrical shock can occur.
OBSERVED FAULT
POSSIBLE CAUSE
REMEDY
Heater ignites, but
fl
ame-out con-
trol shutsoff heater after a short
period of time
1. Wrong pump pressure
2. Dirty air output, air intake, and lint
fi
lters
3. Dirty fuel
fi
lter
4. Dirt in nozzle
5. Dirty photocell lens
6. Bad
fl
ame-out control
1. See
Pump Pressure Adjustment
, page
10.
2. See
Air Output, Air Intake and Lint Filters
, page
10
3. See
Fuel Filter
, page 8
4. See
Nozzle
, page 11
5. Clean photocell lens
6. Replace
fl
ame-out control
Heater will not ignite, but motor
runs for ashort period of time
1. Wrong pump pressure
2. Carbon deposits on spark plug and/
orimproper gap
3. Dirty fuel
fi
lter
4. Dirt in nozzle
5. Water in fuel tank
6. Electronic ignitor not grounded (earthed)
7. Bad electronic ignitor
1. See
Pump Pressure Adjustment
, page 7
2. See
Spark Plug
, page 6
3. See
Fuel Filter
, page 6
4. See
Nozzle
, page 8
5. Drain and
fl
ush fuel tank with clean kerosene.
See
Storing, Transporting, or Shipping
.
6. Make sure electronic ignitor mountingis tight
7. Replace electronicignitor
Motor does not start when heater
is pluggedin, fan rotates slowly or
does not turn
1. Flame-out control not reset
2. Binding pump rotor
1. Reset
fl
ame-out control button, see Figures 5
and 6, page 4
2. If fan is hard to turn, see
Pump Rotor
, page 9
WARNING: High voltage!
PREVENTATIVE MAINTENANCE SCHEDULE
TROUBLESHOOTING
