Ryobi RLT1830H13 5133002102 - Инструкция по эксплуатации - Страница 6

4

| English

 WARNING

Servicing requires extreme care and knowledge 

DQG VKRXOG EH SHUIRUPHG RQO\ EH D TXDOL¿HG VHUYLFH

technician. For service we suggest you return the 
product to your nearest authorized service center for 
repair. When servicing, use only identical replacement 
parts.

Ŷ

Ensure the battery is disconnected and the supply cord 
is disconnected from the supply before performing any 
maintenance, cleaning or adjustments.

Ŷ

<RX PD\ PDNH DGMXVWPHQWV DQG UHSDLUV GHVFULEHG

here. For other repairs, contact the authorized service 
agent.

Ŷ

For replacement line use only nylon filament line of 
the diameter described in the specification table of this 
manual

Ŷ

After extending new cutter line, always return the 
product to its normal operating position before starting.

Ŷ

After each use, clean the product with a soft dry cloth. 
Any part that is damaged should be properly repaired or 
replaced by an authorized service centre.

Ŷ

Check all nuts, bolts and screws at frequent intervals 
for proper tightness to ensure the product is in safe 
working condition.

INTENDED USE

The product is only intended for use outdoors.
The product is designed for cutting grass, light weeds 
and other similar vegetation at or about ground level. 
The cutting plane should be approximately parallel to the 
ground surface when trimming and approximately vertical 
when edging.
The product should not be used to cut or trim hedges, 
bushes or other vegetation where the cutting plane is not at 
or about ground surface level.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The following hazards may arise in use and the 
operator should pay special attention to avoid the following: 

Ŷ

Injury caused by vibration. Hold the tool by designated 
handles and restrict working time and exposure.

Ŷ

Exposure to noise can cause hearing injury. Wear ear 
protection and limit exposure.

RISK REDUCTION

It has been reported that vibrations from hand-held tools 
may contribute to a condition called Raynaud’s Syndrome 
in certain individuals. Symptoms may include tingling, 

QXPEQHVV DQG EODQFKLQJ RI WKH ¿QJHUV XVXDOO\ DSSDUHQW

upon exposure to cold. Hereditary factors, exposure to 
cold and dampness, diet, smoking and work practices are 
all thought to contribute to the development of the these 
symptoms. There are measures that can be taken by the 
operator to possibly reduce the effects of vibration:

Ŷ

Keep your body warm in cold weather. When operating 

the unit wear gloves to keep the hands and wrists 
warm. It is reported that cold weather is a major factor 
contributing to Raynaud’s Syndrome.

Ŷ

After each period of operation, exercise to increase 
blood circulation.

Ŷ

Take frequent work breaks. Limit the amount of 
exposure per day.

If you experience any of the symptoms of this condition, 
immediately discontinue use and see your doctor about 
these symptoms.

 WARNING

Injuries may be caused, or aggravated, by prolonged 
use of a tool. When using any tool for prolonged periods, 
ensure you take regular breaks.

KNOW YOUR PRODUCT

See page 129.

Parts

1. Rear handle
2. Lock-out trigger
3. Trigger
4. Cord retainer
5. Front handle
6.  Handle adjusting knob
7. Upper shaft
8. Telescopic collar
9. Rotating collar
10. Lower shaft
11. Safety guard
12. Cut-off blade
13. Cutting line
14. Battery pack
15. Battery latch button
16. Charger
17. Spool cover
18. Spool cover lock button
19. Spool
20. Eyelet
21. Line release button
22. Slot

SYMBOLS ON THE PRODUCT

Safety alert 

Read and understand all instructions 
before operating the product, follow all 
warnings and safety instructions.

Wear ear protection.

Wear eye protection.