Bosch GCM 10 SD - Инструкция по эксплуатации - Страница 37

 English | 

37

Bosch Power Tools

1 609 92A 0XL | (29.9.14)

Adjusting the Clamping Force of Clamp 3 (see figure V)

The clamping force of the handle clamp 

3

 can be readjusted.

Checking:

– The clamping force of the clamp must securely hold the 

handle in any of the 4 possible positions.

Adjusting:

– Open clamp 

3

.

– Turn both set screws 

70

 in anticlockwise direction with the 

supplied hex key 

47

 (1.5 mm) to reduce the clamping 

force, or increase the clamping force by turning in clock-
wise direction.
Always adjust both set screws to the same height.

– Shut  clamp 

3

 and check if the desired clamping force has 

been reached.

Aligning the Angle Indicator (Horizontally) (see figure W)

– Bring the power tool into the working position.
– Turn the saw table 

16

 to the 0 ° detent 

15

. The lever 

13

must be felt to engage in the detent.

Checking:

The angle indicator 

71

 must be in alignment with the 0 ° mark 

of the scale 

38

.

Adjusting:

– Loosen the fastening screw of the angle indicator with the 

supplied cross-head screwdriver 

33

 and align the angle in-

dicator alongside the 0 ° mark.

– Retighten the screw again.

Aligning the Fence

– Bring the machine into the transport position.
– Turn the saw table 

16

 to the 0 ° detent 

15

. The lever 

13

must be felt to engage in the detent.

Checking:

 (see figure X1)

– Adjust an angle gauge to 90 ° and position it flush with the 

saw blade 

7

 between the fence 

18

 and the saw blade on 

the saw table 

16

.

The leg of the angle gauge must be flush with the fence over 
the complete length.

Adjusting:

 (see figure X2)

– Loosen the locking screws 

20

 on bothe sides of the fence 

extensions 

19

.

Loosen the setting screws 

72

 with the supplied hex key 

33

(4 mm).

– Remove the fence extensions.
– Loosen all hex socket screws 

73

 with the supplied socket 

spanner 

33

 (14 mm). 

– Turn the fence 

18

 until the angle gauge is flush over the 

complete length.

– Retighten the hex socket screws 

73

.

– Retighten the fence extensions. Tighten the setting screws 

72

 only to the extent, that the fence extensions can be 

moved easily.

Transport (see figure Y)

Before transporting the power tool, the following steps must 
be carried out:
– Loosen the locking screw 

29

 if tightened. Pull the tool arm 

completely to the front and tighten the locking screw 
again.

– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to 

the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.

– Carry the power tool by the transport handles 

28

 and 

2

 or 

via the recessed grips 

74

 on the side of the saw table.



The power tool should always be carried by two per-
sons in order to avoid back injuries.



When transporting the power tool, use only the trans-
port devices and never use the protective devices.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself, pull the mains 
plug.

If the replacement of the supply cord is necessary, this has 
to be done by Bosch or an authorized Bosch service agent in 
order to avoid a safety hazard.

Cleaning

For safe and proper working, always keep the power tool and 
its ventilation slots clean.

The retracting blade guard must always be able to move freely 
and retract automatically. Therefore, always keep the area 
around the retracting blade guard clean.

Remove dust and chips after each working procedure by 
blowing out with compressed air or with a brush.

Clean the roller 

9

 regularly.

Accessories

Quick-action clamp . . . . . . . . . . . . . . . . . . . . .  2 608 040 205

Insert plates. . . . . . . . . . . . . . . . . . . . . . . . . . .  2 607 960 021

Dust bag set. . . . . . . . . . . . . . . . . . . . . . . . . . .  2 605 411 212

Extension bars (435 mm)  . . . . . . . . . . . . . . .  2 607 001 956

Saw blades for wood and plate materials, panels and 
strips/mouldings

Saw blade 254 x 30 mm, 60 teeth  . . . . . . . .  2 608 640 436

OBJ_BUCH-1128-003.book  Page 37  Monday, September 29, 2014  12:25 PM