Мойки высокого давления Karcher CB 1 25 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
30
English
220
Drive-in door 1 is not closed
Light barriers of
the doors are
dirty, interfer-
ence in door
control.
Clean light bar-
riers of the
doors.
221
Drive-in door 1 is not opened
222
Drive-out door 2 is not opened
223
Drive-out door 2 is not closed
226
Light barrier door 1 blocked on the outside
227
Light barrier door 1 blocked on the inside
228
Light barrier door 2 blocked on the outside
229
Light barrier door 2 blocked on the inside
234
Light barrier Position 1 blocked (HD-/Chemical start)
Light barriers
dirty/defective
Clean light bar-
riers.
235
Light barrier Position 2 blocked. (positioning light barrier)
236
Light barrier Drier forward blocked
237
Light barrier Drier in the middle blocked
238
Light barrier Drier behind blocked
Faults without display
Fault
Possible cause
Remedy
of whom
Cleaning effect in-
adequate
None or too little detergent, none or too little
air pressure in the supply line, worn brushes
Check filling level of the detergent; if necessary fill
up; vent dosing pumps. Check air pressure, if neces-
sary adjust (0.5 Mpa (5 bar) at the manometer main-
tenance unit). Clean detergent suction, check
detergent supply lines for damage, check brushes
and if necessary replace.
Operator
Too little water or
none is coming out
of the jets.
Dirt catcher is blocked, water pressure insuf-
ficient, jets blocked, magnet valve or supply
line defective
Clean dirt catcher, check water supply pressure and
pumps, clean jets with compressed air, service mag-
net valves and supply lines (water und electricity) if
necessary.
Operator
Water still comes
out of the the jets af-
ter the end of the
wash
Magnet valve dirty
Clean magnet valves.
Custom-
er Service
Drying insufficient
Too little or too much drying aid, false drying
aid, none or too little air pressure
Increase or decrease dosage, check filling level of
the detergent, clean suction filter, vent dosing pump,
use original drying aid from Kärcher, check function
of the blow-out drier.
Operator
Wheel wash brush
does not turn.
Contact pressure is too high
Reduce contact pressure at the pressure lessener
for wheel wash (Diag. 1).
Operator
Move wheel wash
brush slowly or not
out
None or too little air pressure
Check air pressure (about. 0.275 MPa (2.75 bar)), if
necessary adjust, increase contact pressure at the
pressure lessener for wheel wash (Fig. 1).
Operator
Wheel wash brush
moves out on the
false side
Light barriers dirty
Clean light barriers, if necessary check setting.
Operator/
Custom-
er Service
Brushes dirty fast
Shampoo dosage too low
Adjust shampoo, check water amount, adjust if nec-
essary.
Operator
Jet pipes of the un-
derfloor wash oscil-
late too slowly/fast
or not at all.
None or too little air pressure
Check air pressure in the supply line, if necessary
adjust.
Operator
Oscillating unit strongly dirtied.
Clean oscillating unit.
Operator/
Custom-
er Service
Throttles falsely set.
Reset throttles.
Operator/
Custom-
er Service
Plant without func-
tion
Fault in the voltage supply
See to fault-free voltage supply according to connec-
tion values.
Operator/
Electri-
cians
Portal is driven out
beyond limit switch
for the ends of the
drive-rails
Limit switch falsely set
Check distance between limit switch and switch flag
(nominal: 4mm).
Operator/
Custom-
er Service
