Bosch 0.601.B23.100 - Инструкция по эксплуатации - Страница 39

English | 

39

– Set the required mitre and/or bevel angle.
– Switch on the power tool.
– Slowly guide the tool arm downwards using the

handle 

(13)

.

– Saw through the workpiece applying uniform feed.
– Switch off the power tool and wait until the saw blade has

come to a complete stop.

– Slowly guide the tool arm upwards.

Sawing with slide movement

– For cuts made using the slide device 

(37)

 (wide work-

pieces), loosen the locking screw 

(6)

 if it is clamping the

slide device in place.

– Firmly clamp the workpiece as appropriate for its dimen-

sions.

– Set the required mitre and/or bevel angle.
– Pull the tool arm away from the fences 

(2)

 and 

(1)

 until

the saw blade is in front of the workpiece.

– Switch on the power tool.
– Slowly guide the tool arm downwards using the

handle 

(13)

.

– Now push the tool arm towards the fences 

(2)

 and 

(1)

and saw through the workpiece with uniform feed.

– Switch off the power tool and wait until the saw blade has

come to a complete stop.

– Slowly guide the tool arm upwards.

Sawing workpieces of the same length (see figure Q)

The length stop 

(55)

 (accessory) can be used for easily saw-

ing workpieces of the same length.
The length stop can be mounted on either side of the saw
table extension 

(29)

.

– Loosen the locking screw 

(56)

 and move the length

stop 

(55)

 over the clamping screw 

(57)

.

– Re-tighten the locking screw 

(56)

.

– Set the saw table extension 

(29)

 to the required length.

Adjusting the Depth Stop (Sawing the Groove) (see
figure R)

The depth stop needs to be adjusted if you wish to saw a
groove.
– Swivel the depth stop 

(42)

 forwards.

– Swivel the tool arm by the handle 

(13)

 into the required

position.

– Turn the adjusting screw 

(41)

 until the end of the screw

touches the depth stop 

(42)

.

– Slowly guide the tool arm upwards.

Sawing wider mouldings (see figure S)

For sawing wider mouldings (max. height of 175 mm), use
the spacer 

(7)

.

– If tightened, loosen the locking screw 

(6)

 and pull the tool

arm forwards.

– Move the spacer 

(7)

 down onto the slide mechanism 

(37)

and slide the tool arm as far back as possible.

– Re-tighten the locking screw 

(6)

.

Special workpieces

When sawing curved or round workpieces, these must be es-
pecially secured against slipping. At the cutting line, there
should be no gap between the workpiece, fence and saw
table.
If necessary, you will need to manufacture special fixtures.

Adjusting the laser

Note:

 To test the laser function, the power tool must be con-

nected to the power supply.

u

While adjusting the laser (e.g. when moving the tool
arm), never activate the on/off switch.

 Starting the

power tool accidentally can lead to injuries.

– Bring the power tool into the work position.
– Turn the saw table 

(20)

 to the 0° detent 

(27)

. The lever

(24)

 must be felt to engage in the detent.

Checking (see figure T1)

– Draw a straight cutting line on the workpiece.
– Slowly guide the tool arm downwards using the

handle 

(13)

.

– Position the workpiece so that the teeth of the saw blade

line up with the cutting line.

– Hold the workpiece in this position and slowly guide the

tool arm back up.

– Clamp the workpiece.
– Turn on the laser beam using the switch 

(34)

.

The laser beam must be flush with the cutting line on the
workpiece along its entire length, even if the tool arm is
guided downwards.

Adjusting the flush alignment (see figure T2)

1. Adjusting the right-hand laser beam:
– Turn the set screw 

(58)

 with the hex key 

(59)

 until the

right-hand laser beam is flush with the marked cutting line
on the workpiece along the entire length.
This also moves the left-hand laser beam.

One rotation anticlockwise moves the laser beam from left to
right; one rotation clockwise moves the laser beam from
right to left.
2. Adjusting the left-hand laser beam:
– Turn the set screw 

(60)

 with the hex key 

(59)

 until the

left-hand laser beam is at the same distance from the
marked cutting line on the workpiece as the right-hand
laser beam.

One rotation anticlockwise moves the laser beam from left to
right; one rotation clockwise moves the laser beam from
right to left.

Adjusting the parallelism (see figure T3)

– Remove the four screws 

(61)

 from the laser protection

cap 

(15)

 with a cross-headed screwdriver.

Note:

 To reach the front screws of the laser protection

cap, you must swing the retracting blade guard 

(16)

backwards.

– Remove the laser protection cap 

(15)

.

Bosch Power Tools

1 609 92A 5U9 | (20.10.2020)