Bosch GTS 10 J - Инструкция по эксплуатации - Страница 35

 English | 

35

Bosch Power Tools

1 609 92A 15R | (26.1.15)

– Adjust the blade guard according to the workpiece height.

When sawing, the blade guard must always face lightly 
against the workpiece.

– Switch on the machine.
– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has 

come to a complete stop.

Sawing Bevel Angles

– Adjust the desired bevel angle. (see “Adjusting Bevel An-

gles”, page 33)

– Follow the worksteps in section “Sawing Straight Cuts” ac-

cordingly.

Sawing Mitre Angles (see figure S)

– Adjust the requested mitre angle. (see “Adjusting Mitre An-

gles”, page 33)

– Place the workpiece against profile rail 

28

.

The profile may not be on the cutting line. If so, loosen 
knurled nut 

53

 and move the profile.

– Raise or lower the saw blade with the crank 

19

 so that the 

upper saw teeth project approx. 5 mm above the work-
piece surface.

– Adjust the blade guard according to the workpiece height.

When sawing, the blade guard must always face lightly 
against the workpiece.

– Switch on the machine.
– With one hand, press the workpiece against the profile rail 

and with the other hand, slowly move the angle stop via 
locking knob 

49

 toward the front in guide groove 

5

.

– Switch off the machine and wait until the saw blade has 

come to a complete stop.

Checking and Adjusting the Basic Adjustment

To ensure precise cuts, the basic adjustment of the machine 
must be checked and adjusted as necessary after intensive use.
A certain level of experience and appropriate specialty tools are 
required for this.

A Bosch after-sales service station will handle this mainte-
nance task quickly and reliably.

Setting the Stops for Standard 0 °/ 45 ° Bevel Angles

– Bring the power tool into the working position.
– Adjust to a 0 ° bevel angle.
– Tilt the blade guard 

6.x

 toward the rear to the stop.

Checking:

 (see figure T1)

– Set an angle gauge to 90 ° and place it on the saw table 

9

.

The leg of the angle gauge must be flush with the saw blade 

26

over the complete length.

Adjusting:

 (see figure T2)

– Loosen screw 

54

.

The 0 ° stop 

55

 can now be moved.

– Loosen locking lever 

17

.

– Move handwheel 

18

 toward the 0° stop until the leg of the 

angle gauge is flush with the saw blade over the complete 
length.

– Hold the handwheel in this position and tighten locking le-

ver 

17

 again.

– Tighten  screw 

54

 again.

When the angle indicator 

47

 is not in line with the 0 ° mark of 

scale 

48

, loosen screw 

56

 with a commercially available 

cross-head screwdriver and align the angle indicator along-
side the 0 ° mark.

Repeat the above mentioned worksteps accordingly for the 
45 ° bevel angle (loosening screw 

57

; moving the 45° stop 

58

). In this, the angle indicator 

47

 must not be misadjusted.

Parallelism of the Saw Blade to the Guide Grooves of the 
Angle Stop (see figure  U)

– Bring the power tool into the working position.
– Tilt the blade guard 

6.x

 toward the rear to the stop.

Checking:

– With a pencil, mark the first visible saw tooth on the left 

side that projects above the insert plate.

– Set an angle gauge to 90 ° and place it on the edge of the 

guide groove 

5

. 

– Move the leg of the angle gauge until it touches the marked 

saw tooth, and read the clearance between saw blade and 
guide groove.

– Turn the saw blade until the marked tooth projects above 

the right side of the insert plate.

– Move the angle gauge alongside the guide groove to the 

marked tooth.

– Measure the clearance between the saw blade and guide 

groove again.

Both clearances measured must be identical.

Adjusting:

– Loosen hex socket screws 

59

 at the front below the saw ta-

ble and hex socket screws 

60

 at the rear below the saw ta-

ble with the supplied hex key 

21

.

– Carefully move the saw blade until it is parallel to guide 

groove 

5

.

– Retighten  all  screws 

59

 and 

60

 again.

Adjusting the Saw Table’s Clearance Indicator 
(see figure V)

– Position the parallel guide on the right side of the saw 

blade.
Move the parallel guide until the mark in the lens 

27

 indi-

cates 26 cm on the bottom scale.

To lock the parallel guide, press clamping handle 

35

 down 

again.

– Loosen tensioning lever 

15

 and pull the table extension out 

to the stop.

Checking:

On the upper scale 

1

, clearance indicator 

51

 must indicate the 

identical value as the mark in lens 

27

 on the bottom scale 

1

.

Adjusting:

– Loosen screw 

61

 with a cross-head screwdriver and align 

clearance indicator 

51

 alongside the 26 cm mark of the up-

per scale 

1

.

OBJ_BUCH-1325-003.book  Page 35  Monday, January 26, 2015  1:18 PM