Bosch GTS 10 J - Инструкция по эксплуатации - Страница 28

28

 | English 

1 609 92A 15R | (26.1.15)

Bosch Power Tools

Safety Warnings for Table Saws



Never stand on the power tool. 

Serious injuries can occur 

when the power tool tips over or when inadvertently com-
ing into contact with the saw blade.



Take care that the blade guard operates properly and 
can move freely. 

Always adjust the blade guard in such a 

manner that it faces loosely against the workpiece when 
sawing. Never clamp the blade guard when it is open.



Keep hands away from the cutting area while the ma-
chine is running. 

Danger of injury when coming in contact 

with the saw blade.



Never reach behind the saw blade in order to hold the 
workpiece, remove saw dust/wood chips or for any oth-
er reason. 

The clearance of your hand to the rotating saw 

blade is too small.



Guide the workpiece against the saw blade only when 
the machine is switched on. 

Otherwise there is damage 

of kickback, when the saw blade becomes wedged in the 
workpiece.



Keep handles dry, clean, and free from oil and grease. 

Greasy, oily handles are slippery causing loss of control.



Operate the power tool only when the work area to the 
workpiece is clear of any adjusting tools, wood chips, 
etc. 

Small pieces of wood or other objects that come in 

contact with the rotating saw blade can strike the operator 
with high speed.



Only saw one workpiece at a time. 

Workpieces placed on 

top or aside of each other can cause the saw blade to jam 
or the workpieces to move against each other while saw-
ing.



Always use the parallel guide or the angle guide. 

 This 

improves the cutting accuracy and reduces the possibility 
of saw blade binding.



Use the machine for grooving or rebating only with an 
appropriately suitable protective device (e. g. a tunnel 
blade guard).



Do not use the machine for cutting slots (stopped 
grooves).



Use the machine only for cutting the materials listed 
under Intended Use. 

Otherwise, the machine can be sub-

ject to overload.



If the saw blade should become jammed, switch the ma-
chine off and hold the workpiece until the saw blade 
comes to a complete stop. To prevent kickback, the 
workpiece may not be moved until after the machine 
has come to a complete stop. 

Correct the cause for the 

jamming of the saw blade before restarting the machine.



Do not use dull, cracked, bent or damaged saw blades. 

Unsharpened or improperly set saw blades produce nar-
row kerf causing excessive friction, blade binding and kick-
back.



Always use blades with correct size and shape (dia-
mond versus round) of arbour holes. 

Blades that do not 

match the mounting hardware of the saw will run eccentri-
cally, causing loss of control.



Do not use high speed steel (HSS) saw blades. 

Such saw 

blades can easily break.



Do not touch the saw blade after working before it has 
cooled. 

The saw blade becomes very hot while working.



Keep your workplace clean. 

Blends of materials are par-

ticularly dangerous. Dust from light alloys can burn or ex-
plode.



Never operate the machine without the insert plate. 
Replace a defective insert plate. 

Without flawless insert 

plates, injuries are possible from the saw blade.



Check the cable regularly and have a damaged cable re-
paired only through an authorised customer service 
agent for Bosch power tools. Replace damaged exten-
sion cables. 

This will ensure that the safety of the power 

tool is maintained.



Store the machine in a safe manner when not being 
used. The storage location must be dry and lockable. 

This prevents the machine from storage damage, and from 
being operated by untrained persons.



Never leave the machine before it has come to a com-
plete stop. 

Cutting tools that are still running can cause in-

juries.



Never use the machine with a damaged cable. Do not 
touch the damaged cable and pull the mains plug when 
the cable is damaged while working. 

Damaged cables in-

crease the risk of an electric shock.

Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols can be important for the operation of 
your power tool. Please memorise the symbols and their 
meanings. The correct interpretation of the symbols helps 
you operate the power tool better and more secure.

Symbols and their meaning

Keep hands away from the cutting area 
while the machine is running. 

Danger of 

injury when coming in contact with the saw 
blade.

Wear a dust respirator.

OBJ_BUCH-1325-003.book  Page 28  Monday, January 26, 2015  1:18 PM