Bosch GCM 10 J - Инструкция по эксплуатации - Страница 28

28

 | English 

1 609 92A 0XH | (12.12.14)

Bosch Power Tools

Aligning the Angle Indicator (Horizontally) (see figure N)

– Bring the power tool into the working position.
– Turn  the  saw  table 

6

 to the 0 ° detent 

11

. The lever 

9

 must 

be felt to engage in the detent.

Checking:

The angle indicator 

10

 must be in alignment with the 0 ° mark 

of the scale 

12

.

Adjusting:

– Loosen the screw 

43

 with the cross-head screwdriver pro-

vided and align the angle indicator along the 0 ° mark.

– Retighten the screw again.

Aligning the Angle Indicator (Vertically) (see figure O)

– Bring the power tool into the working position.
– Turn  the  saw  table 

6

 to the 0 ° detent 

11

. The lever 

9

 must 

be felt to engage in the detent.

– Tilt the tool arm until it faces against the stop screw 

27

 for 

the 0 ° bevel angle and then tighten the clamping lever 

19

again.

Checking:

The angle indicator 

41

 must be in alignment with the 0 ° mark 

of the scale 

44

.

Adjusting:

– Loosen the screw 

45

 with the cross-head screwdriver pro-

vided and align the angle indicator along the 0 ° mark.

– Retighten the screw again.
– Afterwards, check to ensure that the adjustment made is 

correct for the 45 ° mark.

Aligning the Fence

– Bring the machine into the transport position.
– Turn  the  saw  table 

6

 to the 0 ° detent 

11

. The lever 

9

 must 

be felt to engage in the detent.

Checking:

 (see figure P1)

– Adjust an angle gauge to 90 ° and position it flush with the 

saw blade 

36

 between the fence 

5

 and the saw blade on 

the saw table 

6

.

The leg of the angle gauge must be flush with the fence over 
the complete length.

Adjusting:

 (see figure P2)

– Loosen all hex socket screws 

29

 with the hex key 

28

 pro-

vided.

– Turn the fence 

5

 until the angle gauge is flush over the com-

plete length.

– Retighten the screws again.

Setting the Standard Bevel Angle 0 ° (Vertical)

– Bring the machine into the transport position.
– Turn the saw table 

6

 until it engages at 0 °.

Checking:

 (see figure Q1)

– Set an angle gauge to 90 ° and place it on the saw table 

6

.

The leg of the angle gauge must be flush with the saw blade 

36

over the complete length.

Adjusting:

 (see figure Q2)

– Loosen the lock lever 

19

.

– Loosen the lock nut of the stop screw 

27

 using a commer-

cial box-end or open-end spanner (size 13 mm).

– Screw the stop screw in or out until the leg of the angle 

gauge is flush with the saw blade over the complete length.

– Retighten the lock lever 

19

 again.

– Afterwards, retighten the lock nut of the stop screw 

27

again. 

In case the angle indicator 

41

 is not in a line with the 0 ° mark 

of the scale 

44

 after the adjustment, loosen the screw 

45

 us-

ing a commercial cross-head screwdriver and align the angle 
indicator along the 0 ° mark.

Setting the Standard Bevel Angle 45 ° (Vertical)

– Bring the power tool into the working position.
– Turn the saw table 

6

 until it engages at 0 °.

– Loosen the lock lever 

19

 and tilt the tool arm leftward to 

the stop (45 °) by the handle 

2

.

Checking:

 (see figure R1)

– Set an angle gauge to 45 ° and place it on the saw table 

6

.

The leg of the angle gauge must be flush with the saw blade 

36

over the complete length.

Adjusting:

 (see figure R2)

– Loosen the lock nut of the stop screw 

18

 using a commer-

cial box-end or open-end spanner (size 13 mm).

– Screw the stop screw in or out until the leg of the angle 

gauge is flush with the saw blade over the complete length.

– Retighten the lock lever 

19

 again.

– Afterwards, retighten the lock nut of the stop screw 

18

again.

In case the angle indicator 

41

 is not in a line with the 45 ° mark 

of the scale 

44

, firstly check the 0 ° setting for the bevel angle 

and the angle indicator again. Then repeat the adjustment of 
the 45 ° bevel angle.

Transport

Before transporting the power tool, the following steps must 
be carried out:

– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to 

the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.

– Carry the machine by the transport handle 

23

 or hold it by 

the recessed handles 

15

 on the sides of the saw table.



When transporting the power tool, use only the trans-
port devices and never use the protective devices.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself, pull the mains 
plug.

If the replacement of the supply cord is necessary, this has to 
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.

OBJ_BUCH-1156-002.book  Page 28  Friday, December 12, 2014  10:16 AM