Pioneer VSX-920 / VSX-1020 / VSX-1025 - Инструкция по эксплуатации - Страница 89

The Advanced MCACC menu

10

89

En

English

Français

Deutsch

Nederlands

Italiano

Español

6

Wait for the Auto MCACC Setup to finish 

outputting test tones.

A progress report is displayed on-screen while 

the receiver outputs test tones to determine the 

speakers present in your setup. Try to be as 

quiet as possible while it’s doing this.

1

• With error messages (such as 

Too much 

ambient noise!

 or 

Check microphone

) 

select 

RETRY

 after checking for ambient 

noise (see 

Problems when using the Auto 

MCACC Setup

 on page 42) and verifying the 

mic connection. If there doesn’t seem to be 

a problem, you can simply select 

GO NEXT

and continue.

7

If necessary, confirm the speaker 

configuration in the GUI screen.

2

The configuration shown on-screen should 

reflect the actual speakers you have.
If no operations are performed for 10 seconds 

while the speaker configuration check screen 

is being displayed, the Auto MCACC Setup will 

resume automatically. In this case, you don’t 

need to select ‘

OK

’ and press 

ENTER

 in step 8.

• If you see an 

ERR

 message (or the speaker 

configuration displayed isn’t correct), there 

may be a problem with the speaker 

connection.

If selecting 

RETRY

 doesn’t work, turn off 

the power and check the speaker 
connections. If there doesn’t seem to be a 

problem, you can simply use 

/

 to select 

the speaker and 

/

 to change the 

setting and continue. 

• If 

Reverse Phase

 is displayed, the 

speaker’s wiring (+ and –) may be 

inverted. Check the speaker connections.

3

– 

If the connections were wrong, turn off 

the power, disconnect the power cord, 

then reconnect properly. After this, 
perform the Full Auto MCACC procedure 
again.

– If the connections were right, select 

GO 

NEXT 

and 

continue.

8

Make sure ‘OK’ is selected, then press 

ENTER.

2

A progress report is displayed on-screen while 

the receiver outputs more test tones to 

determine the optimum receiver settings for 

channel level, speaker distance, and Acoustic 

Calibration EQ.
Again, try to be as quiet as possible while this 
is happening. It may take 3 to 7 minutes.

• If you selected a 

STAND.WAVE Multi-P

setup (in step 2), you will be asked to place 
the mic at the 2nd and 3rd reference 
points before finally placing it at your main 

listening position.

9

The Auto MCACC Setup procedure is 

completed and the Advanced MCACC menu 
reappears automatically.

The settings made in the Auto MCACC Setup 

should give you excellent surround sound 
from your system, but it is also possible to 
adjust these settings manually using the 

Manual MCACC

 setup menu (starting below) 

or 

Manual SP Setup

 menu (starting on 

page 100).

4

Note

1 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

2 This screen is only shown if you selected 

ALL

 or 

Speaker Setting

 from the 

Auto MCACC

 menu.

3 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase 

(dipole speakers, reflective speakers, etc.), 

Reverse Phase

 may be displayed even if the speakers are properly 

connected.

4 • Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm will 

end up with different size settings. You can correct the setting manually using the 

Manual speaker setup

 on page 100.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting 

should be accurate (taking delay and room characteristics into account) and generally does not need to be changed.

• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing 

environment, we recommend adjusting the settings manually.

VSX-1020_SYXCN.book  89 ページ  

年

月

日　金曜日　午前９時

分