Усилители Pioneer VSX-920 / VSX-1020 / VSX-1025 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
The Advanced MCACC menu
10
88
En
After a single calibration is performed, each of
the following three correction curves can be
stored separately in the MCACC memory.
SYMMETRY
implements symmetric
correction for each pair of left and right
speakers to flatten the frequency-amplitude
characteristics.
ALL CH ADJ
is a ‘flat’ setting
where all the speakers are set individually so
no special weighting is given to any one
channel.
FRONT ALIGN
1
sets all speakers in
accordance with the front speaker settings (no
equalization is applied to the front left and right
channels).
•
THX Speaker
(only available when the
Auto MCACC
Menu above is
ALL
or
Speaker Setting
)
– Select
YES
if you are
using THX speakers (set all speakers to
SMALL
), otherwise leave it set to
NO
.
•
STAND.WAVE Multi-P
(only available when
the
Auto MCACC
Menu above is
EQ Pro &
S-Wave
)
– In addition to measurements at
the listening position, you can use two more
reference points for which test tones will be
analyzed for standing waves. This is useful if
you want to get a balanced ‘flat’ calibration
for several seating positions in your
listening area.
2
Place the microphone at the
reference point indicated on-screen and
note that
the last microphone placement will
be at your main listening position:
3
Connect the microphone to the MCACC
SETUP MIC jack on the front panel.
Make sure there are no obstacles between the
speakers and the microphone.
If you have a tripod, use it to place the
microphone so that it’s about ear level at your
normal listening position. If you do not have a
tripod, use some other object to install the
microphone.
3
4
When you’re finished setting the options,
select START then press ENTER.
5
Follow the instructions on-screen.
• Make sure the microphone is connected.
• If you’re using a subwoofer, it is
automatically detected every time you
switch on the system. Make sure it is on
and the volume is turned up.
• See
Problems when using the Auto MCACC
Setup
on page 42 for notes regarding high
background noise levels and other possible
interference.
Note
1 If you selected
ALL
or
Keep SP System
as your
Auto MCACC
menu, you can specify the MCACC preset where you
want to save the
SYMMETRY
,
ALL CH ADJ
and
FRONT ALIGN
settings.
2 Switch the
Multi-P
setting
NO
if you only use one listening position.
1
2
3
2nd reference
point
3rd reference
point
Main listening
position
3 Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make accurate
measurement impossible:
• Sofas or other soft surfaces.
• High places such as tabletops and sofa tops.
MASTER
VOLUME
MCACC
SETUP MIC
VIDEO CAMERA
iPod
iPhone
USB
HDMI 5
CONTROL
ON / OFF
Microphone
Tripod
VSX-1020/VSX-1025
VSX-1020_SYXCN.book 88 ページ
年
月
日 金曜日 午前９時
分
