Pioneer VSX-920 / VSX-1020 / VSX-1025 - Инструкция по эксплуатации - Страница 41

Basic Setup

04

41

En

English

Français

Deutsch

Nederlands

Italiano

Español

4

Press 

 and then select START.

5

Follow the instructions on-screen.

Make sure the microphone is connected, and if 

you’re using a subwoofer, make sure it is 
switched on and set to a comfortable volume 
level.

6

Wait for the test tones to finish, then 

confirm the speaker configuration in the GUI 
screen.

A progress report is displayed on-screen while 
the receiver outputs test tones to determine the 

speakers present in your setup. Try to be as 
quiet as possible while it’s doing this.

1

If no operations are performed for 10 seconds 
while the speaker configuration check screen 

is being displayed, the Auto MCACC Setup will 
resume automatically. In this case, you don’t 
need to select ‘

OK

’ and press 

ENTER

 in step 7.

• With error messages (such as 

Too much 

ambient noise!

 or 

Check microphone.

), 

select 

RETRY

 after checking for ambient 

noise (see 

Problems when using the Auto 

MCACC Setup

 on page 42) and verifying the 

mic connection. If there doesn’t seem to be 
a problem, you can simply select 

GO NEXT

and continue.

The configuration shown on-screen should 
reflect the actual speakers you have.

• If  you  see  an 

ERR

 message (or the speaker 

configuration displayed isn’t correct), 

there may be a problem with the speaker 
connection.

If selecting 

RETRY

 doesn’t work, turn off 

the power and check the speaker 

connections. If there doesn’t seem to be a 

problem, you can simply use 

/

 to 

select the speaker and 

/

 to change 

the setting and continue. 

• If 

Reverse Phase

 is displayed, the 

speaker’s wiring (+ and –) may be 

inverted. Check the speaker connections.

2

– 

If the connections were wrong, turn off 

the power, disconnect the power cord, 

then reconnect properly. After this, 

perform the Full Auto MCACC procedure 

again.

– If the connections were right, select 

GO 

NEXT 

and 

continue.

7

Make sure ‘OK’ is selected, then press 

ENTER.

A progress report is displayed on-screen while 

the receiver outputs more test tones to 

determine the optimum receiver settings for 

Channel Level, Speaker Distance, Standing 

Wave and Acoustic Cal EQ.
Again, try to be as quiet as possible while this 

is happening. It may take 3 to 10 minutes.

8

The Auto MCACC Setup procedure is 

completed and the Home Menu menu 
reappears automatically.

3

Be sure to disconnect the microphone from 

this receiver upon completion of the Auto 
MCACC Setup.

Note

1 Do not adjust the volume during the test tones. This may result in incorrect speaker settings.

RECEIVER

Now Analyzing... 

2/9

Environment Check

1a.Full Auto MCACC

A/V RECEIVER

E x i t

C a n c e l

Ambient Noise 

:  OK

Microphone : 
Speaker YES/NO 

:

L : YES
FHL : 

YES

C :  YES
FHR : 

YES

R :  YES
SR : 

  YES

SBR : 

YES

SBL : 

YES

SL :  YES
SW : 

YES

1a.Full Auto MCACC

10

 OK 

RETRY

A/V RECEIVER

E x i t

C a n c e l

2 If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase 

(dipole speakers, reflective speakers, etc.), 

Reverse Phase

 may be displayed even if the speakers are properly 

connected.

3 You can also choose to view the settings from the 

MCACC Data Check

 screen. See 

Checking MCACC Data

 on page 96 

for more on this.

VSX-1020_SYXCN.book  41 ページ  

年

月

日　金曜日　午前９時

分