Усилители Pioneer VSX-920 / VSX-1020 / VSX-1025 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
The System Setup and Other Setup menus
11
104
En
1
Select ‘Speaker Distance’ from the
Manual SP Setup menu.
2
Adjust the distance of each speaker using
/
.
You can adjust the distance of each speaker in
0.01 m increments.
3
When you’re finished, press RETURN.
You will return to the
Manual SP Setup
menu.
Tip
• For best surround sound, make sure the
surround back speakers are the same
distance from the listening position.
X-Curve
Most soundtracks mixed for cinema sound too
bright when played back in large rooms. The X-
Curve setting acts as a kind of re-equalization
for home theater listening, and restores proper
tonal balance of movie soundtracks.
1
1
Select ‘X-Curve’ from the Manual SP
Setup menu.
2
Choose the X-Curve setting you want.
Use
/
to adjust the setting. The X-Curve is
expressed as a downwards slope in decibels
per octave, starting at 2 kHz. The sound
becomes less bright as the slope increases (to
a maximum of
–3.0dB/oct
). Use the following
guidelines to set the X-Curve according to your
room size:
• If you select
OFF
, the frequency curve will
be flat and the X-Curve has no effect.
3
When you’re finished, press RETURN.
Network Setup menu
Set up the network to listen to Internet radio on
this receiver.
1
Press
on the remote control,
then press HOME MENU.
A Graphical User Interface (GUI) screen
appears on your TV. Use
///
and
ENTER
to navigate through the screens and
select menu items. Press
RETURN
to confirm
and exit the current menu.
2
Select ‘System Setup’ from the Home
Menu.
3
Select ‘Network Setup’ from the System
Setup menu.
4
Select the setting you want to adjust.
If you are doing this for the first time, you may
want to adjust these settings in order:
•
IP Address, Proxy
– Sets up the IP
address/Proxy of this receiver (see below).
•
Information
– Checks the MAC address of
this receiver (page 105).
IP address/Proxy setting
In case the router connected to the LAN
terminal on this receiver is a broadband router
(with a built-in DHCP server function), simply
turn on the DHCP server function, and you will
not need to set up the network manually. You
must set up the network as described below
only when you have connected this receiver to
a broadband router without a DHCP server
function. Before you set up the network,
consult with your ISP or the network manager
for the required settings. It is advised that you
also refer to the operation manual supplied
with your network component.
2
Note
1 Since the principal is the same, X-Curve isn’t applied when you’re using the Pure direct mode.
Room size (m
2
)
≤
36
≤
48
≤
60
≤
72
≤
300
≤
1000
X-Curve
(dB/oct)
–0.5 –1.0 –1.5 –2.0
–2.5
–3.0
2 In case you make changes to the network configuration without the DHCP server function, make the corresponding
changes to the network settings of this receiver.
RECEIVER
VSX-1020_SYXCN.book 104 ページ
年
月
日 金曜日 午前９時
分
