Усилители Pioneer VSX-920 / VSX-1020 / VSX-1025 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Additional information
12
110
En
Other audio problems
No sound from subwoofer.
• Check that the subwoofer is connected properly, switched on and the volume
turned up.
• If your subwoofer has a sleep function, make sure it is switched off.
• Make sure that the Subwoofer setting is
YES
or
PLUS
(see
Speaker Setting
on
page 102).
• The crossover frequency may be set too low; try setting it higher to match the
characteristics of your other speakers (see
Speaker Setting
on page 102).
• If there is very little low frequency information in the source material, change
your speaker settings to Front:
SMALL
/ Subwoofer:
YES
, or Front:
LARGE
/
Subwoofer:
PLUS
(see
Speaker Setting
on page 102).
• Check that the LFE channel is not set to
OFF
, or to a very quiet setting (see
Setting the Audio options
on page 68).
• Check the speaker level settings (see
Channel Level
on page 103).
No sound from one speaker. • Check the speaker connection (see
Connecting the speakers
on page 20).
• Check the speaker level settings (see
Channel Level
on page 103).
• Check that the speaker hasn’t been set to
NO
(see
Speaker Setting
on page 102).
• The channel may not be recorded in the source. By using one of the advanced
effect listening modes, you may be able to create the missing channel (see
Listening in surround sound
on page 57).
Sound is produced from
analog components, but not
from digital ones (DVD, LD,
CD-ROM, etc.).
• Check that the input signal type is set to
DIGITAL
(see
Choosing the input
signal
on page 61).
• Make sure that the digital input is assigned correctly for the input jack the
component is connected to (see
The Input Setup menu
on page 42).
• Check the digital output settings on the source component.
• If the source component has a digital volume control, make sure this is not
turned down.
No sound is output or a noise
is output when Dolby Digital/
DTS software is played back.
• Check that your DVD player is compatible with Dolby Digital/DTS discs.
• Check the digital output settings of your DVD player. Make sure that the DTS
signal output is set to On.
• If the source component has a digital volume control, make sure this is not
turned down.
No sound when using the
Home Menu
.
• If the HDMI input function is selected, sound is muted until exiting the
Home
Menu
.
Symptom
Remedy
Broadcast stations cannot be
selected automatically, or
there is considerable noise in
radio broadcasts.
For FM broadcasts
• Fully extend the FM wire antenna, adjust the position for best reception and
secure to a wall, etc.
• Use an outdoor antenna for better reception (see page 31).
For AM broadcasts
• Adjust the position and direction of the AM antenna.
• Use an outdoor antenna for better reception (see page 31).
• Noise may be caused by interference from other equipment, such as a
fluorescent light, motor, etc. Switch off or move the other equipment, or move
the AM antenna.
Symptom
Remedy
VSX-1020_SYXCN.book 110 ページ
年
月
日 金曜日 午前９時
分
