STIGA MULTICLIP 547 D 298471848/ST2 - Инструкция по эксплуатации - Страница 81

5

Use  of  unapproved  fuels  will  cause  damage  to 

engine  components,  which  will  not  be  covered 

under warranty

.

 NOTE 

 Only use the fuel named in the technical 

data table. Do not use other types of fuel. It is 

possible to use ecological fuels, such as alkylate 

petrol. The composition of this petrol has less of 

an impact on people and animals. No negative 

effects have been reported in connection to their 

use. Nonetheless, there are types of alkylate 

petrol on the market for which it is not possible 

to provide specific indications on their use.

 3.7  OIL

Use always high quality oils, choosing 

their viscosity grade according to 

the operating temperature.

• 

Only use detergent oil with a 

quality of no less than SF-SG. 

• 

Choose the SAE viscosity based 

on the technical data table.

• 

The use of multigrade oil can lead to greater 

consumption in hot weather, accordingly it is 

necessary to check the level more frequently.

• 

Do not mix oils of different brands 

and characteristics.

• 

SAE 30 oil, if used below +5°C, could 

result in possible engine damage 

due to inadequate lubrication.

 3.8  AIR FILTER

The air filter must always be in perfect 

working order, to prevent debris and dust 

from getting sucked into the engine, reducing 

the efficiency and life of the machine.

• 

Always keep the filtering element free of 

debris and in perfect working order (par. 5.6).

• 

If necessary, replace the filtering 

element with an original spare part 

Incompatible filtering elements can impair 

the efficiency and life of the engine.

• 

Never start the engine without mounting 

the filtering element properly.

 3.9  SPARK PLUG

Not all the spark plugs for endothermic 

engines are the same.

• 

Use only spark plugs of the recommended 

type, with the right heat range.

• 

Check the length of the thread, 

because - if too long - it will damage 

the engine beyond repair.

• 

Make sure that the electrodes are clean 

and that their gap is correct (par. 5.7)

4.  REGULATIONS FOR USE

 4.1  BEFORE EACH USE

Before every use, perform the following checking 

procedures in order to assure a regular operation.

 4.1.1 

Oil level check

1. 

Place the machine on a flat surface.

2. 

Clean around the oil fill cap.

3. 

Unscrew the cap(fig. 2.A), clean the end of 

the dipstick (fig. 2.B) and slide it back in until 

the cap is touching the hole, as shown :

–

if the dipstick is short, place the 

cap without fastening it,

–

if the dipstick is long, fasten it again 

with a click and then unscrew it,

4. 

Remove the cap with the dipstick and 

check the oil level that must be between 

the «MIN» and «MAX» marks.

5. 

If oil is required, add oil of the same kind 

up to the «MAX» mark, being careful 

not to spill any outside the oil fill

6. 

Fully tighten the filler cap (fig. 2.A) 

and wipe off any spilled oil.

 NOTE 

 Top up gradually, adding small amounts 

of oil, checking the level each time.

Do not top up beyond the «MAX» level; 

an excessive level can cause:

• 

smoking from the exhaust;

• 

soiling of the spark plug or air filter with 

subsequent difficulty for ignition.

 NOTE 

 For the required type of oil, observe the 

indications provided in the technical data table.

 4.1.2 

Air filter control

The  efficiency  of  the  air  filter  is  essential  to  correct 

engine  operation;  never  start  the  engine  if  the  filter 

element is missing, broken or insufficiently saturated 

with oil.

1.

   Clean around the filter cover (fig.4.A).

2.

   Remove  the  cover  (fig.  4.A)  by  releasing  the 

tabs (fig. 4.B);

3

.   Check the state of the filtering element (fig. 4.C 

or  4.C.1),  which  must  be  intact,  clean  and  in 

perfect  working  order;  if  not,  either  carry  out 

maintenance or replace it (see 5.6).

4.

  Put the cover back in place (fig. 4.A).