Bosch GCM 216 - Инструкция по эксплуатации - Страница 24

24

 | English

Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Mitre saw with mounted saw blade
– Screw clamp 

(22)

– Hex key 

(32)

– Extension bar 

(21)

 with securing screw 

(38)

 (2 x)

– Length gauge 

(10)

– Dust bag 

(1)

Note:

 Check the power tool for possible damage.

Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.

Fitting individual components

– Carefully remove all parts included in the delivery from

their packaging.

– Remove all packing material from the power tool and the

accessories provided.

Fitting the extension bar (see figure A)

The free end of long and heavy workpieces must have some-
thing placed underneath it or be supported.
To extend the saw table further, extension bars can be
mounted both to the left or right of the power tool.
– Unscrew the securing screw 

(38)

 from the extension bar

with a cross-headed screwdriver.

– Tilt the power tool.
– Push the extension bars 

(21)

 on both sides of the power

tool all the way into the corresponding drill holes .

– For the pull-out safety device, screw the securing

screw 

(38)

 back into the extension bar.

Stationary or flexible mounting

u

To ensure safe handling, the power tool must be
mounted on a flat, stable work surface (e.g. work
bench) before use.

Mounting on a work surface (see figure B1−B2)

– Use suitable screw fasteners to secure the power tool to

the work surface. The holes 

(19)

 are used for this pur-

pose.

or

– Firmly clamp the base of the power tool to the work sur-

face with commercially available screw clamps.

Mounting on a Bosch saw stand

With the height-adjustable legs, Bosch GTA saw stands
provide firm support for the power tool on any surface. The
workpiece supports of the saw stand are used for underlay-
ing long workpieces.

u

Read all the warnings and instructions included with
the saw stand.

 Failure to observe the warnings and fol-

low instructions may result in electric shock, fire and/or
serious injury.

u

Assemble the saw stand properly before mounting the
power tool.

 Correct assembly is important to prevent the

risk of collapsing.

– Mount the power tool on the saw stand in the transport

position.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity. 
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.

u

Avoid dust accumulation at the workplace. 

Dust can

easily ignite.

The dust/chip extraction system can be blocked by dust,
chips or fragments of the workpiece.
– Switch the power tool off and pull the mains plug out of

the socket.

– Wait until the saw blade has come to a complete stop.
– Determine the cause of the blockage and eliminate it.

Self-generated dust extraction (see figure C)

For basic chip collection, use the dust bag 

(1)

 provided.

– Attach the dust bag 

(1)

 to the chip ejector 

(31)

.

During sawing, the dust bag must not come into contact with
moving tool components.
Always empty the dust bag in good time.

u

Check and clean the dust bag each time after using.

u

When sawing aluminium, remove the dust bag to avoid
the risk of fire.

External Dust Extraction

You can also attach a dust extraction hose (

36

 mm dia-

meter) to the chip ejector 

(31)

 for extraction.

– Connect the dust extraction hose to the chip ejector 

(31)

.

The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.

1 609 92A 6DZ | (15.03.2021)

Bosch Power Tools