Bosch GTM 12 JL - Инструкция по эксплуатации - Страница 44

44

 | English 

1 609 92A 1T0 | (28.10.15)

Bosch Power Tools

Permissible Workpiece Dimensions
Maximum

 workpiece sizes:

Minimum

 workpiece sizes (= all workpieces that can be 

clamped left or right from the saw blade with a screw clamp):
200 x 40 mm (length x width)

Cutting depth, max.

(0 °/0 °): 95 mm

Replacing the Insert Plate (see figure

L)

The red insert plate 

24

 can become worn after long use of the 

power tool.

Replace defective insert plates.

– Bring the power tool into the chop and mitre saw working 

position.  (see “Working Position”, page 42)

– Unscrew  screws 

49

 using a cross-head screwdriver and re-

move the old insert plate.

– Insert the new insert plate and and screw all screws 

49

 in 

again.

– Set the vertical bevel angle to 0 ° and saw through the in-

sert plate.

– Afterwards, set the vertical bevel angle to 45 ° and saw into 

the cut again.
This procedure achieves that the insert plate is as close as 
possible to the teeth of the saw blade without touching it.

Sawing

Cutting Off

– Firmly clamp the workpiece as appropriate for its dimen-

sions.

– Adjust the requested mitre and/or bevel angle.
– Switch on the machine.
– Push button 

17

 and slowly guide the tool arm downward 

with the handle 

18

.

– Saw through the workpiece applying uniform feed.
– Switch off the machine and wait until the saw blade has 

come to a complete stop.

– Guide the tool arm slowly upward.

Special Workpieces

When sawing curved or round workpieces, these must be es-
pecially secured against slipping. At the cutting line, no gap 
may exist between workpiece, fence and saw table.

Provide for special fixtures, if required.

Sawing Profile Strips/Mouldings (Floor and Ceiling Strips)

Profile strips/mouldings can be sawn in two different ways:

– Placed against the fence
– Lying flat on the saw table.

Always make trial cuts with the mitre angle setting first on 
scrap wood.

Floor Strips/Mouldings

The following table contains instructions for sawing floor strips/mouldings.

Mitre/Bevel Angle

Height x Width 

[mm]

Horizontal

Vertical

0 °

0 °

95 x 150

45 ° (leftward/right-

ward)

0 °

95 x 90

0 °

45 °

60 x 150

45 ° (leftward)

45 °

60 x 60

45 ° (rightward)

45 °

60 x 100

Settings

Placed 
against the 
fence

Lying flat on 
the saw table

Bevel angle

0 °

45 °

Floor strip/moulding

Left side 

Right side

Left side 

Right side

Inner corner

Horizontal mitre angle

45 ° left

45 ° right

0 °

0 °

Positioning of work-
piece

Bottom edge on 

saw table

Bottom edge on 

saw table

Upper edge against 

the fence 

Bottom edge 

against the fence

The finished work-
piece is located ...

... to the left of the 

cut

... to the right of the 

cut

... to the left of the 

cut

... to the left of the 

cut

Outer corner

Horizontal mitre angle

45 ° right

45 ° left

0 °

0 °

Positioning of work-
piece

Bottom edge on 

saw table

Bottom edge on 

saw table

Bottom edge 

against the fence

Upper edge against 

the fence 

The finished work-
piece is located ...

... to the left of the 

cut

... to the right of the 

cut

... to the right of the 

cut

... to the right of the 

cut

OBJ_BUCH-1688-006.book  Page 44  Wednesday, October 28, 2015  3:13 PM