Триммеры Hitachi CG18DSDL-R4 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
22
English
TROUBLESHOOTING
Use the inspections in the table below if the tool does not
operate normally. If this does not remedy the problem,
consult your dealer or the Hitachi Authorized Ser vice
Center.
Symptom
Possible cause
Remedy
Charger
The Charge lamp
does not go on.
The power plug is not connected to an
AC outlet.
Connect the power plug to an AC outlet.
The batter y is not properly connected to
the charger.
Insert the batter y so that it is properly
seated in the charger.
The batter y or charger electrodes are
soiled.
Use a cotton swab or other tool to clean
the electrodes.
The batter y is extremely hot.
Allow the batter y to properly cool before
charging.
The Charge lamp
does not go o
ff
after 4
hours of charging.
The batter y or charger is faulty.
Disconnect the power plug and consult
your dealer or the Hitachi Authorized
Ser vice Center.
Tool
Does not operate.
The rechargeable batter y is depleted.
Charge the rechargeable batter y.
The rechargeable batter y has not been
properly installed.
Remove the rechargeable batter y
from the batter y compartment in
the tool and check for and remove
any foreign matter. Also check the
batter y electrodes for soiling, water
or other foreign matter. Use a cotton
swab for cleaning. Make sure that the
rechargeable batter y is pressed in until
it clicks into place.
The power has not been turned on.
Press the power button on the housing
to start the tool. This tool comes with an
auto power o
ff
function. The power is
automatically turned o
ff
if nobody pulls
the lever during a one minute period
after power on. To turn the tool on again,
press the power button a second time.
Pressing the power button a second
time turns the power o
ff
.
The lock lever was not pressed when
the lever was pulled back.
To prevent accidents from incorrect
operation, the lock lever must be
pressed while the lever is pulled back to
start the motor.
Hold the handle from above and press
the lock lever while pulling the handle.
The tool pulls in large volumes of grass
that are caught between the cover and
the nylon head, the tool is overloaded.
This is the e
ff
ect of a function that
protects the rechargeable batter y by
turning o
ff
the motor when the tool is
exposed to an excessive load. Turn o
ff
the tool and remove the cause of the
overload. Press the power button once
again to continue operation.
Goes on, but soon
stops.
The rechargeable batter y power is low.
Charge the rechargeable batter y.
The rechargeable batter y is overheated. Stop using the rechargeable batter y,
remove it from the tool and let it cool in
a well-ventilated location not exposed
to sunlight.
Strong vibrations
The loop handle is not properly attached
to the main pipe.
Secure properly.
The cover is not been properly attached
to the main pipe.
Secure properly.
000Book̲CG14DSDL̲EE.indb 22
000Book̲CG14DSDL̲EE.indb 22
2011/06/17 14:23:03
2011/06/17 14:23:03
