Karcher (1.174-909.0) - Инструкция по эксплуатации - Страница 5

English

5

use the mains connection cable prescribed by the man-
ufacturer, including when replacing the cable. For order 
no. and type see operating instructions.

● 

Unsuitable 

electrical extension cables can be dangerous. Only use 
approved and appropriately marked electrical extension 
cables with a sufficient cable cross section for outdoors.

● 

Only replace couplings on the power supply or exten-

sion cable using those with the same water density and 
the same mechanical strength. 

몇

CAUTION

● 

In case of longer breaks in opera-

tion and after use, switch off the device at the main 
switch / device switch and pull the mains plug.

ATTENTION

● 

Switch-on procedures will gener-

ate short-term voltage drops.

● 

Unfavourable mains 

conditions may cause other devices to be impaired.

● 

In 

case of a network impedance of less than 0.15 ohms, 
no malfunctions are to be expected.

Water connection

몇

WARNING

● 

The device must not be started 

up if the high-pressure hose is damaged. Replace a 
damaged high-pressure hose at once. Only those 
hoses and connections recommended by the man-
ufacturer may be used. For order no. see 

operating 

instructions

. 

● 

The screw connections of all connection 

hoses must be leak-tight. 

ATTENTION

● 

Observe the regulations at your 

water distribution company.

Operation



DANGER

● 

When using the device in hazard 

zones (e.g. service stations), adhere to the respective 
safety regulations.

● 

Operation in explosive atmos-

pheres is prohibited. 

● 

Never suction solvents, liquids 

containing solvents or undiluted acids. This includes 
e.g. petrol, paint thinner or heating oil. The spray mist is 
highly flammable, explosive and poisonous. 

● 

Dam-

aged wheels / tyre valves are extremely dangerous. 
Damaged wheels / tyre valves can be damaged by the 
high-pressure jet and explode. The first sign of this is 
discolouration of the tyres. Keep a spray distance of at 
least 30 cm when cleaning the wheels / tyre valves.

몇

WARNING

● 

Do not use the device if people 

without the proper protective clothing are in its reach.

● 

With short spray lances, your hand may come into 

contact with the high-pressure jet. Never use a spotlight 
nozzle or rotary nozzle with steel tubes that are shorter 
than 75 cm.

● 

A recoil force will arise due to the water 

stream ejecting from the spray lance. An angular spray 
lance produces a force that acts in upward direction. 
Make sure you grip the gun and spray lance firmly.

● 

When using angular spray units, recoil forces and 

twisting forces may alter.

● 

Do not aim the high-pres-

sure jet at yourself, e.g. to clean clothes or shoes. 

● 

Do 

not direct the high-pressure jet at persons, animals, live 
electrical equipment or at the device itself.

● 

Do not 

spray any objects which contain harmful substances 
(e.g. asbestos). 

● 

Check the device and the accesso-

ries, such as the high-pressure hose, high-pressure gun 
and safety devices, to make sure they are in proper safe 
and reliable condition before each operation. Do not use 
the device if it is damaged. Replace damaged compo-
nents immediately.

● 

Only use high-pressure hoses, 

control panels and couplings specified by the manufac-
turer.

몇

CAUTION

● 

Never leave the device unsuper-

vised while it is in operation. 

● 

Never open the cover 

while the motor is running.

● 

Never clamp the lever of 

the high-pressure gun during operation.

● 

Allow the 

hoses to cool down after hot water operation or operate 
the device briefly using cold water operation.

● 

The de-

vice must be placed on an even, firm subsurface. 

● 

Be-

fore cleaning, carry out a risk assessment of the surface 
to be cleaned to determine any health and safety pro-
tection requirements. The necessary protective meas-
ures must be taken accordingly.

ATTENTION

● 

Do not operate the device at tem-

peratures below 0 °C.

● 

Only clean the motor at wash-

ing stations with an oil separator.

Operation with detergent

몇

CAUTION

● 

Keep the detergent out of the 

reach of children.

● 

When using detergents, observe the 

safety data sheet of the detergent manufacturer, in par-
ticular instructions on protective gear.

● 

Only use the 

detergents supplied or specified by the manufacturer. 
The use of other detergents or chemicals can impair the 
safety of the device.

● 

Never use the recommended de-

tergents undiluted. These products are operationally 
safe since they do not contain any acids, alkali or sub-
stances that are harmful to the environment. Should de-
tergents come into contact with eyes, rinse these out 
immediately and thoroughly using water and seek med-
ical attention immediately. The same applies if deter-
gents are swallowed. 

Device with a hand-arm vibration value > 2.5 m/s² 

(see chapter 

Technical Data

 in the operating 

instructions)

몇

CAUTION

● 

Using the device for longer periods can cause poor 

circulation in the hands due to vibrations. A general 
period of use cannot be set, because this depends on 
several influencing factors:

●

Personal tendency to suffer from poor circulation 
(frequently cold fingers, tingling sensation in the fin-
gers)

●

Low ambient temperature. Wear warm gloves to 
protect your hands.

●

Holding the device too tightly hindering blood circu-
lation.

●

Continuous operation is more harmful than opera-
tion interrupted by work breaks.

You should see a doctor if using the device regularly 
and for lengthy periods of time, and in the event of re-
peated occurrences of symptoms such as tingling in 
the fingers or cold fingers.

Devices with pneumatic tyres

몇

CAUTION

● 

In case of devices with screw-in 

wheel rims: Make sure that all wheel rim bolts are tight-
ened securely before setting the tyre filling pressure.

● 

Make sure that the pressure reducer is set correctly 

on the compressor before setting the tyre filling pres-
sure.

● 

Never exceed the maximum permissible tyre fill-

ing pressure. The tyre filling pressure needs to be read 
on the tyre and if necessary on the wheel rim. If these 
values differ, use the smaller value.