Ryobi RMS18190-0 - Инструкция по эксплуатации - Страница 6

Ŷ

Never reach into the area near the blade unless the 
blade has completely stopped.

Ŷ

Before use, thoroughly check the product and battery 
pack for any damage or material fatigue. Repairs to 
the whole product should only be carried out by an 
authorised service centre.

Ŷ

Always use the guards on the product. Do not use 
the product if the guards are not in place and working 
correctly.

Ŷ

The lower blade guard should only open when the blade 
is lowered to the workpiece and must always be able to 
move freely and close automatically.

Ŷ

$OZD\VIL[DQGXVHH[WHQVLRQEDUVIRUZRUNSLHFHVXSSRUW

during operation.

Ŷ

Never alter of modify the product or its function. Your 
safety may be compromised.

Ŷ

Do not use saw blades which are cracked, damaged or 
deformed.

Ŷ

Do not use saw blades made of high-speed steel.

Ŷ

Only use blades that are sharp. Replace dull blades.

Ŷ

Always use blades with correct size and shape of arbour 
holes. Blades that do not match the mounting hardware 
of the saw will run eccentrically, causing loss of control.

Ŷ

Use only woodworking blades specified in this manual, 
which comply with EN 847-1.

Ŷ

Do not use any flanges, washers and nuts to secure the 
saw blade other than those supplied or indicated in the 
instruction manual.

Ŷ

It is necessary to select a saw blade which is suitable 
for the material being cut. Never use the product to cut 
materials other than those specified in the intended use 
section in this manual.

Ŷ

It is important to avoid overheating the blade and melting 
the plastic when cutting.

Ŷ

,WLVHVVHQWLDOWRDGKHUHWRWKHPD[LPXPVSHHGVSHFLILHG

on the saw blade, only use saw blade that are marked 
with a speed equal or higher than the speed marked on 
the tool.

Ŷ

Replace the table insert when worn or damaged.

Ŷ

Before work, make a dummy cut without the motor turned 
on so the position of the blade, operation of the guards 
with respect to other machine parts, and workpiece may 
be checked.

Ŷ

When performing mitre, bevel or compound mitre cuts, 
adjust the sliding fence or sub-fence to ensure the 
correct clearance from the blade.

Ŷ

Avoid uncontrolled release of the saw unit from the fully 
down position.

Ŷ

The handle lock must always be engaged when 
transporting the product.

Ŷ

Keep the floor area free of loose materials, such as chips 
and cut-offs.

Ŷ

Refrain from removing any cut-offs or other parts of the 
workpiece from the cutting area whilst the product is 
running and the saw head is not in the rest position.

Ŷ

Long workpieces must be adequately supported. The 

ZRUNLQJDUHDRIWKHVDZLQFOXGHVWKHZKROHH[WHQWRIWKH

workpiece. The operator should secure this area from 
accidental contact from other persons or objects which 
may move the workpiece during operation.

Ŷ

The dust produced when using the product may be 
harmful to health. Use a dust suction system and wear 

a suitable dust protection mask. Remove deposited dust 
thoroughly with a vacuum cleaner.

Ŷ

It may be necessary to adjust the sliding fence to ensure 
proper clearance prior to making a bevel or compound 
cut. Make sure the sliding fence lock screw is tightened 
securely after the adjustment.

Ŷ

The clamp can be installed and used on either side of 
the blade. In some operation, the clamp may interfere 
with the blade guard assembly. Always make sure there 
is no interference with the blade guard prior to beginning 
any cutting operation to reduce the risk of serious 
personal injury.

Ŷ

Ambient temperature range for tool during operation is 

EHWZHHQÛ&DQGÛ&

Ŷ

Ambient temperature range for tool storage is between 

Û&DQGÛ&

Ŷ

The recommended ambient temperature range for the 

FKDUJLQJ V\VWHP GXULQJ FKDUJLQJ LV EHWZHHQ  Û& DQG
Û&

ADDITIONAL BATTERY SAFETY WARNINGS

Ŷ

To reduce the risk of fire, personal injury, and product 
damage due to a short circuit, never immerse your 
tool, battery pack or charger in fluid or allow a fluid to 
flow inside them. Corrosive or conductive fluids, such 
as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

Ŷ

Ambient temperature range for battery during use is 

EHWZHHQÛ&DQGÛ&

Ŷ

Ambient temperature range for battery storage is 

EHWZHHQÛ&DQGÛ&

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 

H[SRVHGFRQQHFWRUVZLWKLQVXODWLQJQRQFRQGXFWLYHFDSVRU

tape. Do not transport batteries that are cracked or leaking. 
Check with the forwarding company for further advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The following hazards may arise and the operator 
should pay special attention to avoid the following:

Ŷ

Risk of contact with uncovered parts of the rotating saw 
blade

Ŷ

Kick-back of workpieces or parts of workpieces due to 
improper adjustment or handling

Ŷ

Catapulting of faulty carbide tips from the saw blade

Ŷ

Damage to the respiratory system

NOTE:

 Wear respiratory protection masks containing 

filters appropriate to the materials being worked. Ensure 
adequate workplace ventilation. Do not eat, drink or 
smoke in the work area.

Ŷ

Damage to hearing if effective hearing protection is not 
worn.

WARNING!

 Dust from certain paints, coatings and 

materials may cause irritation or allergic reactions to the 

6

Original Instructions