Ryobi RMS18190-0 - Инструкция по эксплуатации - Страница 5

longer than the table top.

 Workpieces longer or wider 

than the mitre saw table can tip if not securely supported. 
If the cut-off piece or workpiece tips, it can lift the lower 
guard or be thrown by the spinning blade.

Ŷ

Do not use another person as a substitute for a table 
extension or as additional support.

 Unstable support 

for the workpiece can cause the blade to bind or the 
workpiece to shift during the cutting operation pulling 
you and the helper into the spinning blade.

Ŷ

The cut-off piece must not be jammed or pressed 
by any means against the spinning saw blade.

 If 

confined, i.e. using length stops, the cut-off piece could 
get wedged against the blade and thrown violently.

Ŷ

Always use a clamp or a fixture designed to properly 
support round material such as rods or tubing.

 Rods 

have a tendency to roll while being cut, causing the 
blade to “bite” and pull the work with your hand into the 
blade.

Ŷ

Let the blade reach full speed before contacting the 
workpiece.

 This will reduce the risk of the workpiece 

being thrown.

Ŷ

If the workpiece or blade becomes jammed, turn 
the mitre saw off. Wait for all moving parts to stop 
and disconnect the plug from the power source and/
or remove the battery pack. Then work to free the 
jammed material.

 Continued sawing with a jammed 

workpiece could cause loss of control or damage to the 
mitre saw.

Ŷ

After finishing the cut, release the switch, hold the 
saw head down and wait for the blade to stop before 
removing the cut-off piece.

 Reaching with your hand 

near the coasting blade is dangerous.

Ŷ

Hold the handle firmly when making an incomplete 
cut or when releasing the switch before the saw head 
is completely in the down position. 

The braking action 

of the saw may cause the saw head to be suddenly 
pulled downward, causing a risk of injury.

SAFETY INSTRUCTIONS FOR WOOD CUTTING 
BLADE

Ŷ

Please read the manual and instructions carefully before 
using the saw blade and the machine.

Ŷ

The product must be in good condition, the spindle 
without deformation and vibration.

Ŷ

Do not use the product without the guards in position. 
Keep guards in good working order and properly 
maintained.

Ŷ

Ensure the operator is adequately trained in safety 
precautions, adjustment and operation of the product.

Ŷ

Always wear goggles and ear protection when using the 
product. It is recommended to wear gloves, sturdy non 
slipping shoes and apron.

Ŷ

Before using any accessory, consult the instruction 
manual. The improper use of an accessory can cause 
damage and increase the potential for injury.

Ŷ

Use only blades specified in this manual, complying with 
EN 847-1.

Ŷ

2EVHUYHWKHPD[LPXPVSHHGPDUNHGRQWKHVDZEODGH

Ensure the speed marked on the saw blade is at least 
equal to the speed marked on the saw.

Ŷ

Always use blades with correct size and shape of arbour 
holes. Blades that do not match the mounting hardware 
of the saw will run eccentrically, causing loss of control.

Ŷ

Do not use blades of larger or smaller diameter than 
recommended. Do not use any spacers to make the 
blade fit onto the spindle.

Ŷ

Check the tips of the saw blade for damage or abnormal 
appearance before each use. Tips that are damaged or 
loose can become flying objects in use and increase the 
chance of personal injury.

Ŷ

Do not use cracked or distorted saw blades. Do not use 
saw blades that are damaged or deformed.

Ŷ

Scrap the saw blade if damaged, deformed, distorted or 
cracked, repairing is not permitted.

Ŷ

Do not use HSS blades.

Ŷ

Ensure the saw blade is mounted correctly, tighten the 

DUERUQXWVHFXUHO\EHIRUHXVHWLJKWHQLQJWRUTXHDSSUR[

8-10 Nm).

Ŷ

Fastening screw and nuts shall be tightened using the 
appropriate spanner, etc.

Ŷ

([WHQVLRQ RI WKH VSDQQHU RU WLJKWHQLQJ XVLQJ KDPPHU

blows is not permitted.

Ŷ

Make sure the blade and flanges are clean and the 
recessed sides of the collar are against the blade.

Ŷ

Make sure the blade rotates in the correct direction.

Ŷ

Before work, make a dummy cut without the motor turned 
on so the position of the blade, operation of the guards 
with respect to other machine parts and workpiece may 
be checked.

Ŷ

Never leave the product unattended.

Ŷ

Do not apply lubricants on the blade when it is running.

Ŷ

Never perform any cleaning or maintenance work when 
the machine is still running and the head is not in the 
rest position.

Ŷ

Never attempt to stop a machine in motion rapidly by 
jamming a tool or other means against the blade, serious 
accidents can be caused unintentionally in this way.

Ŷ

Disconnect the product from the mains supply or remove 
battery pack before changing blades or carrying out 
maintenance.

Ŷ

Pay attention to blade packing and unpacking, it is easy 
to be injured by the sharp blade tips.

Ŷ

Use a blade holder or wear gloves when handling a saw 
blade.

Ŷ

Keep and store the blade in original packaging or other 
suitable packaging, keep in dry conditions and away 
from chemicals which may damage the blade.

ADDITIONAL SAFETY WARNINGS

Ŷ

Always clamp the workpiece safely and securely.

Ŷ

Ensure that the product is always stable and secure 

HJIL[HGWRDEHQFK

Ŷ

$OZD\V ZHDU HDU SURWHFWRUV ([SRVXUH WR QRLVH FDQ

cause hearing loss.

Ŷ

Always wear safety goggles when using the product. 
It is recommended to wear gloves for handling blades 
and rough material, plus sturdy non slip shoes to protect 
the feet from workpieces which may fall from the cutting 
area.

Ŷ

Disconnect the product from the mains supply or remove 
battery pack before carrying out any maintenance or 
cleaning the product.

Ŷ

Only install the battery pack when the product is 
switched off.

ENGLISH

EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL

5

Original Instructions