Bosch GWS 14 125 Inox - Инструкция по эксплуатации - Страница 23

24

 | English 

1 609 929 R00 | (21.4.08)

Bosch Power Tools

f

Maintain a firm grip on the power tool and 
position your body and arm to allow you to 
resist kickback forces. Always use auxiliary 
handle, if provided, for maximum control 
over kickback or torque reaction during 
start-up. 

The operator can control torque re-

actions or kickback forces, if proper precau-
tions are taken.

f

Never place your hand near the rotating ac-
cessory. 

The accessory may kickback over 

your hand.

f

Do not position your body in the area where 
the power tool will move if kickback occurs. 

Kickback will propel the tool in the direction 
opposite to the wheel’s movement at the 
point of snagging.

f

Use special care when working corners, sharp 
edges, etc. Avoid bouncing and snagging the 
accessory. 

Corners, sharp edges or bouncing 

have a tendency to snag the rotating accessory 
and cause loss of control or kickback.

f

Do not attach a saw chain woodcarving 
blade or toothed saw blade. 

Such blades 

create frequent kickback and loss of control 
over the power tool.

Additional safety instructions for grind-

ing and cutting off operations

f

Use only wheel types that are recommend-
ed for your power tool and the specific 
guard designed for the selected wheel. 

Wheels for which the power tool was not de-
signed cannot be adequately guarded and 
are unsafe.

f

The guard must be securely attached to the 
power tool and positioned for maximum 
safety, so the least amount of wheel is ex-
posed towards the operator. 

The guard 

helps to protect operator from broken wheel 
fragments and accidental contact with 
wheel.

f

Wheels must be used only for recommend-
ed applications. 

For example: do not grind 

with the side of the cut-off wheel. Abrasive 
cut-off wheels are intended for peripheral 
grinding; side forces applied to these wheels 
may cause them to shatter.

f

Always use undamaged wheel flanges that 
are of correct size and shape for your se-
lected wheel. 

Proper wheel flanges support 

the wheel thus reducing the possibility of 
wheel breakage. Flanges for cut-off wheels 
may be different from grinding wheel flanges.

f

Do not use worn down wheels from larger 
power tools. 

Wheels intended for larger 

power tools are not suitable for the higher 
speed of a smaller tool and may burst.

Additional safety warnings specific for 

abrasive cutting off operations

f

Do not “jam” the cut-off wheel or apply ex-
cessive pressure. Do not attempt to make 
an excessive depth of cut. 

Overstressing the 

wheel increases the loading and susceptibili-
ty to twisting or binding of the wheel in the 
cut and the possibility of kickback or wheel 
breakage.

f

Do not position your body in line with and 
behind the rotating wheel. 

When the wheel, 

at the point of operation, is moving away 
from your body, the possible kickback may 
propel the spinning wheel and the power 
tool directly at you.

f

When wheel is binding or when interrupting 
a cut for any reason, switch off the power 
tool and hold the power tool motionless un-
til the wheel comes to a complete stop. Nev-
er attempt to remove the cut-off wheel from 
the cut while the wheel is in motion, other-
wise kickback may occur. 

Investigate and 

take corrective action to eliminate the cause 
of wheel binding.

f

Do not restart the cutting operation in the 
workpiece. Let the wheel reach full speed 
and carefully reenter the cut. 

The wheel may 

bind, walk up or kickback if the power tool is 
restarted in the workpiece.

f

Support panels or any oversized workpiece 
to minimize the risk of wheel pinching and 
kickback. 

Large workpieces tend to sag un-

der their own weight. Supports must be 
placed under the workpiece near the line of 
cut and near the edge of the workpiece on 
both sides of the wheel.

OBJ_BUCH-611-003.book  Page 24  Monday, April 21, 2008  11:28 AM