Bosch 0.601.B23.600 - Инструкция по эксплуатации - Страница 41

 English | 

41

Bosch Power Tools

1 609 929 W31 | (6.4.11)

Minimal

 workpiece sizes

(= all workpieces that can be clamped left or right from the 

saw blade with the supplied material clamp 

22

):

160 x 335 mm (length x width)

Cutting capacity, max.

(0 ° /0 ° ): 104 mm

Sawing

Sawing without Slide Movement (Cutting Off) (see 

figure P)

– Slide glide arm 

28

 completely to the rear and secure it in 

this position (see “Securing the Glide Arm”, page 38).

Make sure that the depth stop 

30

 is pushed completely in-

ward and that adjusting screw 

29

 fits through the recess 

without touching the depth stop when moving the glide 

arm.

– Firmly clamp the workpiece as appropriate for its dimen-

sions.

– Adjust the desired mitre and/or bevel angle.

– Switch on the machine.

– Press locking lever 

5

 and slowly guide the glide arm down-

ward with handle 

4

.

– Saw through the workpiece applying uniform feed.

– Switch off the machine and wait until the saw blade has 

come to a complete stop.

– Slowly guide the glide arm upward.

Sawing with Slide Movement (see figure Q)

f

Before switching on and during the complete sawing, 

hold the handle firmly. While sawing, carry out a con-

trolled motion with the glide arm. 

A moment of inatten-

tion while operating the extremely smooth-running glide 

arm can result in serious personal injury.

– Release glide arm 

28

 (see “Releasing the Glide Arm”, 

page 38).

Check if the complete glide mechanism is operative by 

sliding the glide arm 

28

 back and forth.

– Firmly clamp the workpiece as appropriate for its dimen-

sions.

– Adjust the desired mitre and/or bevel angle.

– Pull the glide arm away from the fence 

10

 until the saw 

blade is in front of the workpiece.

– Switch on the machine.

– Press locking lever 

5

 and slowly guide the glide arm down-

ward with handle 

4

.

– Now, push the glide arm toward the fence 

10

 and saw 

through the workpiece with uniform feed.

– Switch off the machine and wait until the saw blade has 

come to a complete stop.

– Slowly guide the glide arm upward.

Sawing Workpieces of the Same Length (see figure R)

The material stop 

36

 can be used for easily sawing workpiec-

es to the same length.
The material stop can be mounted on either side of the saw ta-

ble extension 

11

.

– Loosen lock screw 

35

 and swing the material stop 

36

 over 

clamping screw 

63

.

– Retighten  lock  screw 

35

.

– Adjust the saw table extension 

11

 to the desired length 

(see “Extending the Saw Table”, page 38).

Adjusting the Depth Stop (Sawing Grooves)

 (see figure S)

The depth stop must be adjusted when sawing a groove or us-

ing a spacer (e.g.: Bosch MSF 110).
– Swivel the depth stop 

30

 outward.

– Press locking lever 

5

 and tilt the glide arm to the desired 

position.

– Turn adjusting screw 

29

, until the screw end touches 

depth stop 

30

.

– Slowly guide the glide arm upward.

Special Workpieces

When sawing curved or round workpieces, these must be es-

pecially secured against slipping. At the cutting line, no gap 

may exist between workpiece, fence and saw table.
Provide for special fixtures, if required.

Sawing Profile Strips/Mouldings 

(Floor and Ceiling Strips)

Profile strips/mouldings can be sawn in two different ways:
– Placed against the fence

– Lying flat on the saw table.
In addition, the cut can be perfomed with or without slide 

movement depending on the width of the profile strip/mould-

ing.
Always make trial cuts with the mitre angle setting first on 

scrap wood.

OBJ_BUCH-1360-001.book  Page 41  Wednesday, April 6, 2011  11:11 AM