Bosch 0.601.B19.100 - Инструкция по эксплуатации - Страница 31

 English | 

31

Bosch Power Tools

1 609 92A 04K | (31.10.12)

Adjusting the Laser
Note: 

To test the laser function, the machine must be con-

nected to power.



While adjusting the laser (e. g. when moving the tool 
arm), never actuate the On/Off switch. 

Accidental start-

ing of the power tool can lead to injuries.

– Bring the power tool into the working position.
– Turn the saw table 

15

 to the 0 °  detent 

24

. The lever 

21

must be felt to engage in the detent.

– Switch the laser beam on with switch 

39

.

Checking:

 (see figure  S1)

– Draw a straight cutting line on the workpiece.
– Press locking switch 

9

 and slowly guide the tool arm down-

ward by the handle 

8

.

– Align the workpiece in such a manner that the teeth of the 

saw blade are in alignment with the cutting line.

– Hold the workpiece in this position and slowly guide the 

tool arm upward again.

– Clamp the workpiece.
The laser beam must be in alignment with the cutting line on 
the workpiece over the complete length, also when the tool 
arm is lowered.

Adjusting:

 (see figure S2)

– Screw the adjustment screw 

52

 in or out using a suitable 

screwdriver until the laser beam is parallel with the cutting 
line on the workpiece over the complete length.

One rotation in anticlockwise direction moves the laser beam 
from left to right; one rotation in clockwise direction moves 
the laser beam from right to left.

Setting the Standard Bevel Angle 0

°

 (Vertical)

– Bring the power tool into the working position.
– Turn the saw table 

15

 to the 0 °  detent 

24

. The lever 

21

must be felt to engage in the detent.

Checking:

 (see figure T1)

– Adjust an angle gauge to 90 °  and position it on the saw ta-

ble 

15

.

The leg of the angle gauge must be flush with the saw blade 

12

over the complete length.

Adjusting:

 (see figure T2)

– Loosen clamping lever 

40

.

– Push  the  stop 

43

 completely to the rear.

– Loosen the lock nut of the stop screw 

53

 using a commer-

cial box-end or open-end spanner (size 10 mm).

– Screw the stop screw in or out until the leg of the angle 

gauge is flush with the saw blade over the complete length.

– Tighten  clamping  lever 

40

 again.

– Afterwards, retighten the lock nut of the stop screw 

53

again. 

In case the angle indicator 

42

 is not in a line with the 0 °  mark 

of the scale 

41

 after the adjustment, loosen the screw 

54

 us-

ing a commercial Phillips screwdriver and align the angle indi-
cator along the 0 °  mark.

Setting the Standard Bevel Angle 45

°

 (Vertical)

– Bring the power tool into the working position.
– Turn the saw table 

15

 to the 0 °  detent 

24

. The lever 

21

must be felt to engage in the detent.

– Turn  the  stop 

30

 completely to the front.

– Loosen clamping lever 

40

 and tilt the tool arm by handle 

8

leftward to the stop (45 ° ).

Checking:

 (see figure U1)

– Adjust an angle gauge to 45 °  and position it on the saw ta-

ble 

15

.

The leg of the angle gauge must be flush with the saw blade 

12

over the complete length.

Adjusting:

 (see figure U2)

– Loosen the lock nut of the stop screw 

55

 using a commer-

cial box-end or open-end spanner (size 10 mm).

– Screw the stop screw in or out until the leg of the angle 

gauge is flush with the saw blade over the complete length.

– Tighten  clamping  lever 

40

 again.

– Afterwards, retighten the lock nut of the stop screw 

55

again.

In case the angle indicator 

42

 is not in a line with the 45 °  mark 

of the scale 

41

, firstly check the 0 °  setting for the bevel angle 

and the angle indicator again. Then repeat the adjustment of 
the 45 °  bevel angle.

Aligning the Angle Indicator (Horizontally) (see figure V)

– Bring the power tool into the working position.
– Turn the saw table 

15

 to the 0 °  detent 

24

. The lever 

21

must be felt to engage in the detent.

Checking:

The angle indicator 

23

 must be in alignment with the 0 °  mark 

of the scale 

17

.

Adjusting:

– Loosen screw 

56

 using a Phillips screwdriver and align the 

angle indicator alongside the 0 °  mark.

– Retighten the screw again.

Transport (see figure X)

Before transporting the power tool, the following steps must 
be carried out:
– Loosen the locking screw 

33

 if tightened. Pull the tool arm 

completely to the front and tighten the locking screw 
again.

– Make  sure  that  the  depth  stop 

32

 is pushed completely in-

ward and that adjusting screw 

4

 fits through the recess 

without touching the depth stop when moving the tool 
arm.

– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to 

the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.

– Wind up the mains cable and tie it together with Velcro 

strap 

58

.

– Carry the machine by the transport handle 

3

 or hold it by 

the recessed handles 

26

 on the sides of the saw table.

OBJ_BUCH-1736-002.book  Page 31  Wednesday, October 31, 2012  3:55 PM