Sparky TV 1835 - Инструкция по эксплуатации - Страница 7

5

Original instructions

EN

5. SERVICE

a) Have your power tool serviced by a qualified 

repair person using only identical replacement 

parts.

 This will ensure that the safety of the power 

tool is maintained.

Chain saw safety warnings

▪

Keep all parts of the body away from the saw 

chain when the motor is operating. Before you 

start the saw, make sure the saw chain is not con-

tacting anything. 

A moment of inattention while op-

erating chain saws may cause entanglement of your 

clothing or body with the saw chain.

▪

Always hold the chain saw with your right hand 

on the rear handle and your left hand on the front 

handle. 

Holding the chain saw with a reserved hand 

configuration increases the risk of personal injury and 

should never be done.

▪

Hold the power tool by insulated gripping surfac-

es only, because the saw chain may contact hid-

den wiring. 

Saw chains contacting a “live” wire may 

make exposed metal parts of the power tool “live” and 

could give the operator an electric shock.

▪

Wear safety glasses and hearing protection. Fur-

ther protective equipment for head, hand, legs 

and feet is recommend. 

Adequate protective cloth-

ing will reduce personal injury by flying debris or ac-

cidental contact with saw chain.

▪

Do not operate a chain saw in a tree. 

Operation of 

a chain saw in a tree, may result in personal injury.

▪

Always keep proper footing and operate the chain 

saw only when standing on fixed, secure and 

level surface. 

Slippery or unstable surfaces such as 

ladders may cause a loss of balance or control of the 

chain saw.

▪

When cutting a limb that is under tension be alert 

for spring back. 

When the tension in the wood fibres 

is released the spring loaded limb may strike the op-

erator and/or throw the chain saw out of control.

▪

Use extreme caution when cutting brush and sap-

lings. 

The slender material may catch the saw chain 

and be whipped toward you or pull you off balance.

▪

Carry the chain saw by the front handle with the 

saw chain stopped and the guide bar pointing to 

the rear. When transporting or storing the chain 

saw always fit the guide bar cover. 

Proper handling 

of the chain saw will reduce the likelihood of acciden-

tal contact with the moving saw chain.

▪

Follow instructions for lubricating, chain ten-

sioning and changing accessories. 

Improperly 

tensioned or lubricated chain may either break or in-

crease the chance for kickback.

▪

Keep handles dry, clean, and free from oil and 

grease. 

Greasy, oily handles are slippery causing 

loss of control.

▪

Cut wood only. Don’t use chain saw for purposes 

not intended – for example – Don’t use chain saw 

for cutting plastic, masonry or non-wood build-

ing materials. 

Use of the chain saw for operations 

different then intended could result in a hazardous 

situation.

Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide 

bar touches an object, or when the wood closes in and 

pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse 

reaction, kicking the guide bar up and back towards the 

operator.

Pinching the saw chain along the top of the guide bar 

may push the guide bar rapidly back towards the opera

-

tor.

Either of these reactions may cause you to lose control of 

the saw which could result in serious personal injury. Do 

not rely exclusively upon the safety devices built into your 

saw. As a chain saw user, you should take several steps 

to keep your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect op

-

erating procedures or conditions and can be avoided by 

taking proper precautions as given below:

▪

Maintain a firm grip, with thumbs and fingers en

-

circling the chain saw handles, with both hands 

on the saw and position your body and arm to al-

low you to resist kickback forces. 

Kickback forces 

can be controlled by the operator, if proper precau-

tions are taken. Do not let go of the chain saw.

Grip the handles 

with the thumbs 

below the handles.

▪

Do not over reach and do not cut above shoulder 

height. This helps prevent unintended tip contact 

and enables better control of the chain saw in un-

expected situations.

▪

Only use replacement bars and chains specified 

by the manufacturer. 

Incorrect replacement bars 

and chains may cause chain breakage and/ or kick-

back.

▪

Follow the manufacturer’s sharpening and main-

tenance instructions for the saw chain. 

Decreas-

ing the depth gauge height can lead to increased 

kickback.

WARNING: 

Before connecting a tool to a 

power  source  ensure  that  the  voltage  supply  is  the 

same as that specified on the nameplate of the tool.

▪ A power source with a voltage greater than that speci-

fied for the tool can result in serious injury to the user, 

as well as damage to the tool.

▪ If in doubt, do not plug in the tool.

▪ Using  a  power  source  with  a  voltage  less  than  the 

nameplate rating is harmful to the motor.

▪ Fully unwind cable drum extensions to avoid potential 

overheating.

▪ When  an  extension  cable  is  required,  you  must  en-

pages-TV-1835-2040-2245-2017.indd   5

11.5.2017 г.   14:42:51