DeLonghi EN560.S - Инструкция по эксплуатации - Страница 85

NL

GR

S TO R I N G E N

Controlelampje brandt niet.

➔

  Controleer de hoofdkabel, de stekker, de netspanning en de zekering. Mocht u problemen ondervinden, neem 

dan telefonisch contact op met 

Nespresso

.

Geen koffie, geen water.

➔

  Het waterreservoir is leeg. Vul het waterreservoir.

➔

  Ontkalk indien nodig, zie hoofdstuk Ontkalking.

De koffie loopt heel traag uit de machine.

➔

  De doorloopsnelheid hangt af van de koffiesoort.

➔

  Ontkalk indien nodig, zie hoofdstuk Ontkalking.

Geen koffie, er komt alleen water uit (ondanks de ingezette capsule).

➔

  Neem telefonisch contact op met 

Nespresso

 bij problemen.

De koffie is niet warm genoeg.

➔

  Verwarm het kopje voor.

➔

  Ontkalk indien nodig, zie hoofdstuk Ontkalking.

Het water lekt weg langs de capsules (water in de bak met capsules).

➔

  Plaats de capsule op de juiste manier. In geval van lekkage, neem telefonisch contact op met 

Nespresso

.

Het controlelampje knippert onregelmatig.

➔

  Laat de machine repareren of neem telefonisch contact op met 

Nespresso

.

Alle lampjes knipperen tegelijk gedurende 10 seconden en dan schakelt 
de machine automatisch uit. 

➔

  Storingsindicatie: machine moet worden gerepareerd. Laat de machine repareren of neem telefonisch contact 

op met 

Nespresso

.

De 6 lampjes knipperen snel 3 keer en daarna is de machine opnieuw 
klaar voor gebruik. 

➔

  Waterreservoir is leeg.

Ontkalking- en reinigingsalarm knipperen.

➔

  De machine zit in de menu modus: houd de knoppen Lungo en melkschuim 3 seconden ingeduwd om het menu 

te verlaten of wacht 30 seconden totdat het automatisch wordt beëindigd.

Het ontkalkingsalarm licht oranje op en de knoppen voor bereiding zijn 
beschikbaar (descaling alarm niveau 1).

➔

  De machine geeft de nood voor ontkalking aan op basis van de  consumptie. Ontkalk de machine. 

Het ontkalkingsalarm knippert oranje en de knoppen voor bereiding 
zijn beschikbaar (descaling alarm niveau 2).

➔

  Het ontkalken werd niet correct uitgevoerd. Ontkalk de machine opnieuw. 

Het ontkalkingsalarm knippert oranje en de knop voor melkschuim 
brandt.

➔

  De machine staat in ontkalkstand. Duw op de knop voor warm melkschuim om het ontkalkingsproces te starten.

Het ontkalkingsalarm licht oranje op en de knoppen voor bereiding zijn 
niet beschikbaar (descaling alarm niveau 3).

➔

  De machine is geblokkeerd door een te grote hoeveelheid kalk. Ontkalk de machine. 

Het reinigingslichtje brandt oranje. 

➔

  Reinig het melksysteem.

Alle koffieknoppen en knoppen voor melkrecepten knipperen 
afwisselend.

➔

  De machine is oververhit, wacht tot de machine is afgekoeld. 

➔

  De machine wordt na het legen van het systeem 10 minuten geblokkeerd.

De capsuleklem kan niet volledig worden gesloten. 

➔

  Maak het capsulereservoir leeg. Ga na of er geen capsule geblokkeerd zit in het capsulereservoir. 

De kwaliteit van het melkschuim is niet volgens de norm.

➔

  Gebruik voor perfect melkschuim magere of halfvolle melk op koelkasttemperatuur (ongeveer 4° C).

➔

  Spoel na elke melkbereiding. (zie sectie R.C.S. met de hand afwassen).

➔

  Ontkalk de machine (zie pagina 80).

➔

  Gebruik geen bevroren melk. 

Het menu is niet toegankelijk.

➔

  Verwijder het melkreservoir.

➔

  Duw de knoppen Lungo en warm melkschuim tegelijk in en houd ze 3 seconden vast.

➔

  Verwijder het ontkalkpijpje.

SPECIFICATIES/

ΤΕΧΝΙΚΑ 

ΧΑΡΑΚΤΉΡΙΣΤΙΚΑ

LATTISSIMA TOUCH

EUR,AUS,NZ: 220240 V, 50/60 Hz, 1300 W
US/CA:

120 V, 60 Hz, 1200 W

19 bar

6.5 kg

1,38 litre

500 ml

13-16 capsules

l=19,4 cm  .  L=33,2 cm  .  h=27,4 cm

Troubleshooting

Contact the Nespressso Club

For any additional information, in case of problems 

or simply to seek advise, call the Nespresso Club. 

Contact details of the Nespresso Club can be found 

in the 'Welcome to Nespresso' folder in your 

machine box or at nespresso.com

No light on display

Check the mains, plug, voltage, and fuse. In case of problems, call the Nespresso Club.

Coffee comes out very slowly.

Flow speed depends on the coffee variety.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Coffee is not hot enough.

Preheat cup.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Capsule area is leaking (water in capsule container). 

Position capsule correctly. If leakages occur, call the Nespresso Club.

Irregular blinking.

Send appliance to repair or call the Nespresso Club.

No coffee, just water runs out (despite inserted capsule).

In case of problems, call the Nespresso Club.

Lever cannot be closed completely

Empty capsule container. Make sure that no capsule is blocked inside the capsule container.

Quality of milk froth is not up to standard

1) For a perfect milk froth, use skimmed or semi-skimmed milk at refrigerator temperature (about 4° C)

2) Rinse after each milk based preparation. Place a recipient under milk outlet, rotate the milk 

regulator knob until “CLEAN” position.

3) Every two days, disassemble the R. C. S. and clean all components in the upper level of a 

dishwasher

Warranty

Delonghi warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. During this period, Delonghi will either repair or 

replace, at its discretion, any defective product at no charge to the owner. Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original 

warranty or six months, whichever is greater. This limited warranty does not apply to any defect resulting from accident, misuse, improper maintenance, or normal wear and tear. Any 

defect resulting from the usage of non genuine Nespresso capsules will not be covered by this warranty. Except to the extent allowed by applicable law, the terms of this limited warranty 

do not exclude, restrict

or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Nespresso for instructions on 

where to send or bring it for repair. Please visit our website at nespresso.com to discover more about Nespresso

Specifications

P

max

Once the rinsing process is finished, the 

machine switches off. Clean the machine 

using a damp cloth. You have now finished 

descaling the machine.

9

10

11

12

Rinsing process 

Rinse and fill water with 

fresh potable water up to MAX level.

Rinsing process 

Place one container of 

minimum 1 litre under both the coffee 

outlet and the hot water spout.

PRESS      to confirm.

The rinsing cycle continues trough the coffee 

outlet, hot water spout and drip tray until the 

water tank is empty.

Water hardness setting

1

programmed buttons blinks 3 times: water hardness is set

i

1”

2

3

4

1
2
3
4
5

Place the water hardness sticker under 

water for 1 second.

The number of red squares indicates 

the water harness level.

Set the value accordingly

Enter the menu, browse the options and select 

WATER HARDNESS.

You will be guided to set the value.

Follow machine display instructions.

max

max

Kg

11

12

EUR, AUS, NZ: 220-240 V,  

50-60 Hz, 1400 W

EUR,AUS,NZ: 220240 V, 50/60 Hz, 1300 W
US/CA:

120 V, 60 Hz, 1200 W

19 bar

6.5 kg

1,38 litre

500 ml

13-16 capsules

l=19,4 cm  .  L=33,2 cm  .  h=27,4 cm

Troubleshooting

Contact the Nespressso Club

For any additional information, in case of problems 

or simply to seek advise, call the Nespresso Club. 

Contact details of the Nespresso Club can be found 

in the 'Welcome to Nespresso' folder in your 

machine box or at nespresso.com

No light on display

Check the mains, plug, voltage, and fuse. In case of problems, call the Nespresso Club.

Coffee comes out very slowly.

Flow speed depends on the coffee variety.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Coffee is not hot enough.

Preheat cup.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Capsule area is leaking (water in capsule container). 

Position capsule correctly. If leakages occur, call the Nespresso Club.

Irregular blinking.

Send appliance to repair or call the Nespresso Club.

No coffee, just water runs out (despite inserted capsule).

In case of problems, call the Nespresso Club.

Lever cannot be closed completely

Empty capsule container. Make sure that no capsule is blocked inside the capsule container.

Quality of milk froth is not up to standard

1) For a perfect milk froth, use skimmed or semi-skimmed milk at refrigerator temperature (about 4° C)

2) Rinse after each milk based preparation. Place a recipient under milk outlet, rotate the milk 

regulator knob until “CLEAN” position.

3) Every two days, disassemble the R. C. S. and clean all components in the upper level of a 

dishwasher

Warranty

Delonghi warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. During this period, Delonghi will either repair or 

replace, at its discretion, any defective product at no charge to the owner. Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original 

warranty or six months, whichever is greater. This limited warranty does not apply to any defect resulting from accident, misuse, improper maintenance, or normal wear and tear. Any 

defect resulting from the usage of non genuine Nespresso capsules will not be covered by this warranty. Except to the extent allowed by applicable law, the terms of this limited warranty 

do not exclude, restrict

or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Nespresso for instructions on 

where to send or bring it for repair. Please visit our website at nespresso.com to discover more about Nespresso

Specifications

P

max

Once the rinsing process is finished, the 

machine switches off. Clean the machine 

using a damp cloth. You have now finished 

descaling the machine.

9

10

11

12

Rinsing process 

Rinse and fill water with 

fresh potable water up to MAX level.

Rinsing process 

Place one container of 

minimum 1 litre under both the coffee 

outlet and the hot water spout.

PRESS      to confirm.

The rinsing cycle continues trough the coffee 

outlet, hot water spout and drip tray until the 

water tank is empty.

Water hardness setting

1

programmed buttons blinks 3 times: water hardness is set

i

1”

2

3

4

1
2
3
4
5

Place the water hardness sticker under 

water for 1 second.

The number of red squares indicates 

the water harness level.

Set the value accordingly

Enter the menu, browse the options and select 

WATER HARDNESS.

You will be guided to set the value.

Follow machine display instructions.

max

max

Kg

11

12

Max/

Max. 

19 bar

EUR,AUS,NZ: 220240 V, 50/60 Hz, 1300 W
US/CA:

120 V, 60 Hz, 1200 W

19 bar

6.5 kg

1,38 litre

500 ml

13-16 capsules

l=19,4 cm  .  L=33,2 cm  .  h=27,4 cm

Troubleshooting

Contact the Nespressso Club

For any additional information, in case of problems 

or simply to seek advise, call the Nespresso Club. 

Contact details of the Nespresso Club can be found 

in the 'Welcome to Nespresso' folder in your 

machine box or at nespresso.com

No light on display

Check the mains, plug, voltage, and fuse. In case of problems, call the Nespresso Club.

Coffee comes out very slowly.

Flow speed depends on the coffee variety.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Coffee is not hot enough.

Preheat cup.

Perform a self check of the machine. Enter the menu list and select Maintenance. Follow instruction

Capsule area is leaking (water in capsule container). 

Position capsule correctly. If leakages occur, call the Nespresso Club.

Irregular blinking.

Send appliance to repair or call the Nespresso Club.

No coffee, just water runs out (despite inserted capsule).

In case of problems, call the Nespresso Club.

Lever cannot be closed completely

Empty capsule container. Make sure that no capsule is blocked inside the capsule container.

Quality of milk froth is not up to standard

1) For a perfect milk froth, use skimmed or semi-skimmed milk at refrigerator temperature (about 4° C)

2) Rinse after each milk based preparation. Place a recipient under milk outlet, rotate the milk 

regulator knob until “CLEAN” position.

3) Every two days, disassemble the R. C. S. and clean all components in the upper level of a 

dishwasher

Warranty

Delonghi warrants this product against defects in materials and workmanship for a period of two years from the date of purchase. During this period, Delonghi will either repair or 

replace, at its discretion, any defective product at no charge to the owner. Replacement products or repaired parts will be guaranteed for only the unexpired portion of the original 

warranty or six months, whichever is greater. This limited warranty does not apply to any defect resulting from accident, misuse, improper maintenance, or normal wear and tear. Any 

defect resulting from the usage of non genuine Nespresso capsules will not be covered by this warranty. Except to the extent allowed by applicable law, the terms of this limited warranty 

do not exclude, restrict

or modify, and are in addition to, the mandatory statutory rights applicable to the sale of the product to you. If you believe your product is defective, contact Nespresso for instructions on 

where to send or bring it for repair. Please visit our website at nespresso.com to discover more about Nespresso

Specifications

P

max

Once the rinsing process is finished, the 

machine switches off. Clean the machine 

using a damp cloth. You have now finished 

descaling the machine.

9

10

11

12

Rinsing process 

Rinse and fill water with 

fresh potable water up to MAX level.

Rinsing process 

Place one container of 

minimum 1 litre under both the coffee 

outlet and the hot water spout.

PRESS      to confirm.

The rinsing cycle continues trough the coffee 

outlet, hot water spout and drip tray until the 

water tank is empty.

Water hardness setting

1

programmed buttons blinks 3 times: water hardness is set

i

1”

2

3

4

1
2
3
4
5

Place the water hardness sticker under 

water for 1 second.

The number of red squares indicates 

the water harness level.

Set the value accordingly

Enter the menu, browse the options and select 

WATER HARDNESS.

You will be guided to set the value.

Follow machine display instructions.

max

max

Kg

11

12

 ~ 4.5 kg/

~ 4.5 κιλά

0.9 Liter/

 Λίτρα

0.35 Liter/

Λίτρα

           17.3 cm/

εκ

  25.8 cm/

εκ

   32 cm/

εκ

85

UM_LATTISSIMA_TOUCH_FACELIFT_Z2A.indb   85

19.10.17   10:01