Bosch GWS 18-125 V-LI - Инструкция по эксплуатации - Страница 23

24

 | English 

1 609 92A 0N2 | (5.6.14)

Bosch Power Tools

The machine must al-
ways work in an up-
grinding motion. Other-
wise, the danger exists 
of it being pushed 

un-

controlled

 out of the 

cut.

When cutting profiles 
and square bar, it is best 
to start at the smallest 
cross section.

Cutting Stone



Provide for sufficient dust extraction when cutting 
stone.



Wear a dust respirator.



The machine may be used only for dry cutting/grinding.

For cutting stone, it is best to use a diamond cutting disc.

When using the cutting guide with dust extraction protection 
guard 

26

, the vacuum cleaner must be approved for vacuum-

ing masonry dust. Suitable vacuum cleaners are available 
from Bosch.

Switch on the machine 
and place the front part 
of the cutting guide on 
the workpiece. Slide the 
machine with moderate 
feed, adapted to the ma-
terial to be worked.

For cutting especially hard material, e. g., concrete with high 
pebble content, the diamond cutting disc can overheat and 
become damaged as a result. This is clearly indicated by cir-
cular sparking, rotating with the diamond cutting disc.
In this case, interrupt the cutting process and allow the dia-
mond cutting disc to cool by running the machine for a short 
time at maximum speed with no load.

Noticeably decreasing work progress and circular sparking 
are indications of a diamond cutting disc that has become 
dull. Briefly cutting into abrasive material (e. g. lime-sand 
brick) can resharpen the disc again.

Information on Structures

Slots in structural walls are subject to the Standard DIN 1053 
Part 1, or country-specific regulations.
These regulations are to be observed under all circumstanc-
es. Before beginning work, consult the responsible structural 
engineer, architect or the construction supervisor.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between 
– 20 ° C and 50 ° C. As an example, do not leave the battery in 
the car in summer.

Occasionally clean the venting slots of the battery using a soft, 
clean and dry brush.

A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.



For safe and proper working, always keep the machine 
and ventilation slots clean.

Please store and handle the accessory(-ies) carefully.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of 
the machine.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange 
the collection of a product in need of servicing or repair. 
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

OBJ_BUCH-1102-006.book  Page 24  Thursday, June 5, 2014  1:02 PM