Бензопилы Oleo-Mac GST 250 5029-9001E2T - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
40
I
GB
F
D
E
SK
P
GR
TR
CZ
RUS
UK
PL
13. TROUBLESHOOTING
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
When you have checked all the possible causes listed and you are still experiencing the problem, see
your Servicing Dealer. If you are experiencing a problem that is not listed in this chart, see your
Servicing Dealer for service.
PROBLEM
POSSIBLE CAUSE
SOLUTION
Engine will not start or will run
only a few seconds after starting.
1. No spark
2. Flooded engine.
1. Watch for spark at spark plug tip. If there
is no spark, repeat test with a new spark
plug (CMR7A).
2. Follow procedure page 28 If engine still
fails to start, repeat procedure with a
new spark plug.
E n g i n e s t a r t s b u t w i l l n o t
accelerate properly or will not run
properly at high speed.
Carburetor requires adjustment.
Contact a Servicing Dealer for carburetor
adjustment.
Engine does not reach full speed
and / or emits excessive smoke
1. Check oil fuel mixture.
2. Air filter dirty.
3. Carburetor requires
adjustment.
1. Use fresh fuel and the correct 2-cycle oil
mix.
2. Clean per instruction in Maintenance-
Air Filter Section.
3. C o n t a c t a S e r v i c i n g D e a l e r f o r
carburetor adjustment.
E n g i n e s t a r t s , r u n s a n d
accelerates but will not idle.
Carburetor requires adjustment.
Tu r n i d l e s p e e d s c r e w “ T ” ( Fi g . 2 8 )
clock wise to increase idle speed.S ee
Operation-Carburetor Adjustment.
Bar and Chain Running Hot and
Smoking
1. Chain oil tank empty.
2. Chain tension too tight.
3. Oiler function.
1. Oil tank should be filled every time that
fuel tank is filled.
2. Te n s i o n c h a i n p e r i n s t r u c t i o n s i n
O p e r a t i o n - C h a i n Te n s i o n s e c t i o n
(Pag.25).
3. Run at full throttle 15 to 30 seconds.
Stop saw and check for oil dripping
from bar tip guard and guide bar. If oil
is present the chain may be dull or bar
may be damaged. If no oil contact a
Servicing Dealer.
Engine starts and runs, but chain
is not rotating
1. Chain brake engaged.
2. Chain tension too tight.
3. Guide bar and chain assembly.
4. Chain and/or guide bar
damaged.
5. Clutch drum and/or rim
sprocket damaged.
1. Release chain brake, see Operation-
Chain Brake Section (Pag.29).
2. Te n s i o n c h a i n p e r i n s t r u c t i o n s i n
O p e r a t i o n - C h a i n Te n s i o n s e c t i o n
(Pag. 25).
3. Refer to Assembly-Assembling the Bar
and Chain Section (Pag.25).
4. Refer to Maintenance -Chain and/or
M a i n t e n a n c e - G u i d e B a r S e c t i o n
(Pag.32).
5. R e p l a c e i f n e c e s s a r y - c o n t a c t a
Servicing Dealer.
W A R N I N G : N e v e r
touch the chain while
the engine is running.
