Ryobi RAG600-115G - Инструкция по эксплуатации - Страница 4

2

| English

)RU H[DPSOH LI DQ DEUDVLYH ZKHHO LV VQDJJHG RU SLQFKHG

by the workpiece, the edge of the wheel that is entering 
into the pinch point can dig into the surface of the material 
causing the wheel to climb out or kick out. The wheel may 
either jump toward or away from the operator, depending 
on the direction of the wheel’s movement at the point of 
pinching. Abrasive wheels may also break under these 
conditions.
Kickback is the result of power tool misuse and/or incorrect 
operating procedures or conditions and can be avoided by 
taking proper precautions as given below.

a) 

Maintain a firm grip on the power tool and 
position your body and arm to allow you to 
resist kickback forces. Always use auxiliary 
handle, if provided, for maximum control 
over kickback or torque reaction during start-
up.

 The operator can control torque reactions or 

kickback forces, if proper precautions are taken.

b) 

Never place your hand near the rotating 
accessory.

 Accessory may kickback over your 

hand.

c) 

Do not position your body in the area where 
power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite 
to the wheel’s movement at the point of snagging.

d) 

Use special care when working corners, sharp 
edges, etc. Avoid bouncing and snagging the 
accessory.

 Corners, sharp edges or bouncing 

have a tendency to snag the rotating accessory 
and cause loss of control or kickback.

e) 

Do not attach a saw chain woodcarving blade 
or toothed saw blade.

 Such blades create 

frequent kickback and loss of control.

ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDING 
OPERATIONS

6DIHW\ZDUQLQJVVSHFL¿FIRUJULQGLQJRSHUDWLRQV

a) 

Use only wheel types that are recommended 
for your power tool and the specific guard 
designed for the selected wheel.

 Wheels for 

which the power tool was not designed cannot be 
adequately guarded and are unsafe.

b) 

The grinding surface of centre depressed 
wheels must be mounted below the plane of 
the guard lip.

 An improperly mounted wheel that 

projects through the plane of the guard lip cannot 
be adequately protected.

c) 

The guard must be securely attached to the 
power tool and positioned for maximum safety, 
so the least amount of wheel is exposed 
towards the operator. 

The guard helps to protect 

the operator from broken wheel fragments, 
accidental contact with wheel and sparks that 
could ignite clothing.

d) 

Wheels must be used only for recommended 
applications. For example: Do not grind with 
the side of cut-off wheel.

 Abrasive cut-off wheels 

are intended for peripheral grinding, side forces 
applied to these wheels may cause them to shatter.

e) 

Always use undamaged wheel flanges that are 
of correct size and shape for your selected 
wheel.

 Proper wheel flanges support the wheel, 

thus reducing the possibility of wheel breakage. 
Flanges for cut-off wheels may be different from 
grinding wheel flanges.

f) 

Do not use worn down wheels from larger 
power tools.

 Wheel intended for larger power tool 

is not suitable for the higher speed of a smaller tool 
and may burst.

ANGLE GRINDER SAFETY PRECAUTIONS

a)  Check that the speed marked on the grinding 

wheel is equal to or greater than the rated speed 
of the product.

b)  Ensure that the dimensions of the grinding wheel 

are compatible with the product and that the wheel 
fits the spindle.

c)  Grinding wheels must be stored in a dry place.

d)  Do not store objects on top of the grinding wheels.

e)  Grinding wheels must not be used for any operation 

other than grinding.

f)  Grinding wheels must be stored and handled 

with care in accordance with the manufacturer’s 
instruction.

g)  Inspect the grinding wheel before use to ensure 

that it is not chipped or cracked. Chips or cracks 
can cause the wheels to shatter, resulting in 
possible serious injury.

h)  Ensure that the wheel is fitted in accordance with 

this manual.

i)  Ensure that the grinding wheel is correctly mounted 

and tightened before use and run the product at 
no-load speed for 30 seconds in a safe position. 
Stop immediately if there is considerable vibration 
or if other defects are detected. If this condition 
occurs, check the product to determine the cause.

j)  Do not use separate reducing bushings or adapters 

to adapt large hole grinding wheels.

k)  Check that the workpiece is properly supported.

l)  Use only grinding wheels approved by RYOBI.

m) Ensure that sparks resulting from use do not 

create a hazard, e.g., do not hit people, or ignite 
flammable substances.

n)  Always use protective safety glasses and ear 

protectors. 

o)  Use other personal protective equipment, such as 

gloves, apron, and helmet, when necessary.

p)  Never place the product on the floor or other 

surfaces while it is running. Grinding wheels 
continue to rotate after the product is switched off. 
Never touch the wheel or place it on the floor or 
other surfaces while it is rotating.

q)  Use the product only for approved applications. 

Never use coolants or water or use the tool as a 

IL[HGWRRO