Bosch 0.601.B19.000 - Инструкция по эксплуатации - Страница 26

26

 | English 

1 609 92A 0HN | (16.6.14)

Bosch Power Tools

Setting the Standard Bevel Angle 45 ° (Vertical)

– Bring the power tool into the working position.
– Turn the saw table 

20

 to the 0 ° detent 

26

. The lever 

24

must be felt to engage in the detent.

– Loosen the lock lever 

8

 and tilt the tool arm leftward to the 

stop (45 °) by the handle 

14

.

Checking:

 (see figure O1)

– Adjust an angle gauge to 45 ° and position it on the saw ta-

ble 

20

.

The leg of the angle gauge must be flush with the saw blade 

38

over the complete length.

Adjusting:

 (see figure O2)

– Loosen the lock lever 

8

.

– Loosen the lock nut of the stop screw 

7

 using a commercial 

box-end or open-end spanner (size 10 mm).

– Screw the stop screw in or out until the leg of the angle 

gauge is flush with the saw blade over the complete length.

– Retighten the lock lever 

8

 again.

– Afterwards, retighten the lock nut of the stop screw 

7

again.

In case the angle indicator 

30

 is not in a line with the 45 ° mark 

of the scale 

29

, firstly check the 0 ° setting for the bevel angle 

and the angle indicator again. Then repeat the adjustment of 
the 45 ° bevel angle.

Aligning the Angle Indicator (Horizontally) (see figure P)

– Bring the power tool into the working position.
– Turn the saw table 

20

 to the 0 ° detent 

26

. The lever 

24

must be felt to engage in the detent.

Checking:

The angle indicator 

22

 must be in alignment with the 0 ° mark 

of the scale 

3

.

Adjusting:

– Loosen screw 

46

 using a cross-head screwdriver and align 

the angle indicator alongside the 0 ° mark.

– Retighten the screw again.

Transport (see figure Q)

Before transporting the power tool, the following steps must 
be carried out:

– Loosen the locking screw 

9

 if tightened. Pull the tool arm 

completely to the front and tighten the locking screw 
again.

– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to 

the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.

– For lifting or transporting, hold the power tool by the re-

cessed grips 

2

 on the side of the saw table 

20

.



When transporting the power tool, use only the trans-
port devices and never use the protective devices.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself, pull the mains 
plug.

If the replacement of the supply cord is necessary, this has to 
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.

Cleaning

For safe and proper working, always keep the power tool and 
its ventilation slots clean.

The retracting blade guard must always be able to move freely 
and retract automatically. Therefore, always keep the area 
around the retracting blade guard clean.

Remove dust and chips after each working procedure by 
blowing out with compressed air or with a brush.

Clean the roller 

18

 regularly.

Accessories

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of 
the machine.

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange 
the collection of a product in need of servicing or repair. 
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com

Article number

Material clamp

1 609 B04 224

Insert plates

1 609 B05 242

Dust bag

1 609 B00 840

Saw blades for wood and plate materials, panels and 
strips/mouldings

Saw blade 216 x 30 mm, 48 teeth

2 608 640 641

Saw blades for plastic and non-ferrous metals

Saw blade 216 x 30 mm, 80 teeth

2 608 640 447

Saw blades for all types of laminate flooring

Saw blade 216 x 30 mm, 60 teeth

2 608 642 133

OBJ_BUCH-2154-002.book  Page 26  Monday, June 16, 2014  2:55 PM