Bosch 0.601.B19.000 - Инструкция по эксплуатации - Страница 22

22

 | English 

1 609 92A 0HN | (16.6.14)

Bosch Power Tools

Technical Data

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU, 
2006/42/EC including their amendments and complies with 
the following standards: EN 61029-1, EN 61029-2-9.

Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 28.04.2014

Noise/Vibration Information

Sound emission values determined according to 
EN 61029-2-9.

Typically the A-weighted noise levels of the product are: 
Sound pressure level 93 dB(A); Sound power level 
106 dB(A). Uncertainty K = 3 dB.

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K 

determined according to EN 61029:
a

h

= 3,0 m/s

2

, K = 1,5 m/s

2

.

The vibration emission level given in this information sheet 
has been measured in accordance with a standardised test 
given in EN 61029 and may be used to compare one tool with 
another. It may be used for a preliminary assessment of expo-
sure.

The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or poorly maintained, 
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns. 

Assembly



Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug 
must not be connected to the mains supply.

Delivery Scope

Before starting the operation of the machine for the first time, 
check if all parts listed below have been supplied:

– Sliding mitre saw with premounted saw blade 
– Material  clamp 

5

– Hex  key 

34

– Metal bar of tilt protector 

33

– Oil  damper 

39

 with 2 fixing screws 

40

Note: 

Check the power tool for possible damage.

Before further use of the machine, check that all protective 
devices are fully functional. Any lightly damaged parts must 
be carefully checked to ensure flawless operation of the tool. 
All parts must be properly mounted and all conditions fulfilled 
that ensure faultless operation.
Damaged protective devices and parts must be immediately 
replaced by an authorised service centre.

Stationary or Flexible Mounting



To ensure safe handling, the machine must be mounted 
on a level and stable surface (e. g., workbench) prior to 
using.

Mounting to a Working Surface (see figure A)

– Fasten the power tool with suitable screw fasteners to the 

working surface. The mounting holes 

1

 serve for this pur-

pose.

Mounting to a Bosch Saw Stand

With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long 
workpieces.



Read all safety warnings and instructions included with 
the worktable. 

Failure to observe safety warnings and in-

structions can lead to electrical shock, fire and/or cause 
serious injuries.

Sliding Mitre Saw

GCM 80 SJ

GCM 800 SJ

GCM 8000 SJ

Article number
3 601 M19 ...

... 0..

... 06.

Rated power input

W

1400

1250

No-load speed

min

-1

5500

5500

Reduced starting current





Weight according to 
EPTA-Procedure 01/2003

kg

13.5

13.5

Protection class

/

II

/

II

Permissible workpiece dimensions (maximal/minimal) see page 25.

The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Dimension of suitable saw blades

Saw blade diameter

mm

210 – 216

Blade body thickness

mm

1.3 – 1.8

Mounting hole diameter

mm

30

Henk Becker
Executive Vice President
Engineering

Helmut Heinzelmann
Head of Product Certification
PT/ETM9

OBJ_BUCH-2154-002.book  Page 22  Monday, June 16, 2014  2:55 PM