Bosch 0.601.B19.000 - Инструкция по эксплуатации - Страница 20

20

 | English 

1 609 92A 0HN | (16.6.14)

Bosch Power Tools

Safety Warnings for Sliding Mitre Saws



Never stand on the power tool. 

Serious injuries can occur 

when the power tool tips over or when inadvertently com-
ing into contact with the saw blade.



Make sure that the guard operates properly and that it 
can move freely. 

Never lock the guard in place when 

opened.



Never remove cutting remainders, wood chips, etc. 
from the sawing area while the machine is running. 

Al-

ways guide the tool arm back to the neutral position first 
and then switch the machine off.



Guide the saw blade against the workpiece only when 
the machine is switched on. 

Otherwise there is danger of 

kickback when the saw blade becomes wedged in the 
workpiece.



Keep handles dry, clean, and free from oil and grease. 

Greasy, oily handles are slippery causing loss of control.



Operate the power tool only when the work area to the 
workpiece is clear of any adjusting tools, wood chips, 
etc. 

Small pieces of wood or other objects that come in 

contact with the rotating saw blade can strike the operator 
with high speed.



Keep the floor free of wood chips and material remain-
ders. 

You could slip or trip.



Always firmly clamp the piece to be worked. Do not saw 
workpieces that are too small to clamp. 

Otherwise, the 

clearance of your hand to the rotating saw blade is too 
small.



Use the machine only for cutting the materials listed 
under Intended Use. 

Otherwise, the machine can be sub-

ject to overload.



If the saw blade should become jammed, switch the ma-
chine off and hold the workpiece until the saw blade 
comes to a complete stop. To prevent kickback, the 
workpiece may not be moved until after the machine 
has come to a complete stop. 

Correct the cause for the 

jamming of the saw blade before restarting the machine.



Do not use dull, cracked, bent or damaged saw blades. 

Unsharpened or improperly set saw blades produce nar-
row kerf causing excessive friction, blade binding and kick-
back.



Always use blades with correct size and shape (dia-
mond versus round) of arbour holes. 

Blades that do not 

match the mounting hardware of the saw will run eccentri-
cally, causing loss of control.



Do not use high speed steel (HSS) saw blades. 

Such saw 

blades can easily break.



Do not touch the saw blade after working before it has 
cooled. 

The saw blade becomes very hot while working.



Never operate the machine without the insert plate. 
Replace a defective insert plate. 

Without flawless insert 

plates, injuries are possible from the saw blade.



Check the cable regularly and have a damaged cable re-
paired only through an authorised customer service 
agent for Bosch power tools. Replace damaged exten-

sion cables. 

This will ensure that the safety of the power 

tool is maintained.



Store the machine in a safe manner when not being 
used. The storage location must be dry and lockable. 

This prevents the machine from storage damage, and from 
being operated by untrained persons.



Secure the workpiece. 

A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.



Never leave the machine before it has come to a com-
plete stop. 

Cutting tools that are still running can cause in-

juries.



Never use the machine with a damaged cable. Do not 
touch the damaged cable and pull the mains plug when 
the cable is damaged while working. 

Damaged cables in-

crease the risk of an electric shock.

Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse (ASTA 
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be 
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should 
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains sock-
et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols can be important for the operation of 
your power tool. Please memorise the symbols and their 
meanings. The correct interpretation of the symbols helps 
you operate the power tool better and more secure.

Symbols and their meaning



Keep hands away from the cutting 
area while the machine is running. 

Danger of injury when coming in con-
tact with the saw blade.



Wear a dust respirator.



Wear safety goggles.



Wear ear protectors. 

Exposure to 

noise can cause hearing loss.

OBJ_BUCH-2154-002.book  Page 20  Monday, June 16, 2014  2:55 PM