Bosch 0.601.B19.000 - Инструкция по эксплуатации - Страница 23

 English | 

23

Bosch Power Tools

1 609 92A 0HN | (16.6.14)



Assemble the worktable properly before mounting the 
power tool. 

Perfect assembly is important in order to pre-

vent the risk of collapsing.

– Mount the power tool in transport position on the saw 

stand.

Flexible Mounting (not recommended!) 
(see figures B1 – B2)

In exceptional cases, when it is not possible to mount the ma-
chine onto a level and stable work surface, it can be set up us-
ing the tilt protector.



Without the metal bar of the tilt protector 33 and the 
tilt protector 25, the power tool will not be stable and 
can tip over especially when sawing maximum mitre 
angles.

– Screw the tilt protector 

25

 in or out until the machine is po-

sitioned level on the working surface.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings, some 
wood types, minerals and metal can be harmful to one’s 
health. Touching or breathing-in the dusts can cause allergic 
reactions and/or lead to respiratory infections of the user or 
bystanders.
Certain dusts, such as oak or beech dust, are considered as 
carcinogenic, especially in connection with wood-treatment 
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.

– Always use dust extraction.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-
rials to be worked.



Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.

The dust/chip extraction can be blocked by dust, chips or 
workpiece fragments.

– Switch the machine off and pull the mains plug from the 

socket outlet.

– Wait until the saw blade has come to a complete stop.
– Determine the cause of the blockage and correct it.

External Dust Extraction

For dust extraction, a vacuum hose (size Ø 35 mm) can also 
be connected to the dust ejector 

11

. 

– Connect the vacuum hose with the sawdust ejector 

11

.

The vacuum cleaner must be suitable for the material being 
worked.

When vacuuming dry dust that is especially detrimental to 
health or carcinogenic, use a special vacuum cleaner.

Changing the Saw Blade (see figures C1 – C4)



When mounting the saw blade, wear protective gloves. 

Danger of injury when touching the saw blade.

Use only saw blades whose maximum permitted speed is 
higher than the no-load speed of the power tool.

Use only saw blades that correspond with the characteristic 
data given in these operation instructions and that are tested 
and marked in accordance with EN 847-1.

Use only saw blades recommended by the tool manufacturer 
and suitable for sawing the materials to be cut.

Removing the Saw Blade

– Bring the power tool into the working position.
– Turn  hex  socket  screw 

35

 with the hex key (5 mm) 

34

 and 

at the same time press the spindle lock 

27

 until it engages.

– Hold the spindle lock 

27

 pressed and unscrew the hex 

socket screw 

35

 in clockwise direction (left-hand thread!).

– Remove the clamping flange 

36

.

– Press locking switch 

15

 and swing back the retracting 

blade guard 

17

 to the stop.

– Hold the retracting blade guard in this position and remove 

the saw blade 

38

.

– Slowly guide the retracting blade guard downward again.

Mounting the Saw Blade

If required, clean all parts to be mounted prior to assembly.

– Press locking switch 

15

, swing back the retracting blade 

guard 

17

 to the stop and hold it in this position.

– Place the new saw blade onto the interior clamping flange 

37

.



When mounting the saw blade, pay attention that the 
cutting direction of the teeth (arrow direction on the 
saw blade) corresponds with the direction of the arrow 
on the blade guard!

– Slowly guide the retracting blade guard downward again.
– Place on the clamping flange 

36

 and the screw 

35

.

Press the spindle lock 

27

 until it engages and tighten the 

screw turning in anticlockwise direction.

Mounting the oil damper (see figure D)

When sawing combination cuts the supplied oil damper must 
be mounted at a certain angle combination (horizontal mitre 
angle > 40 ° and at the same vertical mitre angles > 25 °)

39

.

– Bring the machine into the transport position.
– Screw in the oil damper 

39

 with the 2 fixing screws 

40

 into 

the provided screw holes on the tool arm and the housing, 
using a cross-head screwdriver.

Operation



Before any work on the machine itself, pull the mains 
plug.

Transport Safety (see figure E)

The transport safety-lock 

28

 enables easier handling of the 

machine when transporting to various working locations.

Releasing the Machine (Working Position)

– Push the tool arm by the handle 

14

 down a little in order to 

relieve the transport safety-lock 

28

.

– Pull the transport safety-lock 

28

 completely outward.

– Guide the tool arm slowly upward.

OBJ_BUCH-2154-002.book  Page 23  Monday, June 16, 2014  2:55 PM