Bosch 0.601.B19.000 - Инструкция по эксплуатации - Страница 24

24

 | English 

1 609 92A 0HN | (16.6.14)

Bosch Power Tools

Securing the Machine (Transport Position)

– Loosen the locking screw 

9

 if tightened. Pull the tool arm 

completely to the front and tighten the locking screw 
again.

– To lock the saw table 

20

, tighten the locking knob 

23

.

– Press locking switch 

15

 and slowly guide the tool arm 

downward by the handle 

14

.

– Guide the tool arm downward until the transport safety-

lock 

28

 can be pushed completely inward.

Preparing for Operation

Moving the Fence (see figure F)

You have to move the adjustable fence 

4

 to saw bevel angles.

– Loosen the locking screw 

41

 using the supplied hex key 

34

.

The two outer fixing screws must not be loosened!

– Pull the adjustable fence 

4

 completely outward.

– Retighten the locking screw 

41

.

After sawing the bevel angles, slide the adjustable fence 

4

back again (loosen the locking screw 

41

; slide the fence 

4

completely inward; retighten the locking screw).

Clamping the Workpiece (see figure G)

To ensure optimum working safety, the workpiece must al-
ways be firmly clamped.
Do not saw workpieces that are too small to clamp.

– Press the workpiece firmly against the fences

4

 and 

19

.

– Insert the material clamp 

5

 provided into one of the holes 

42

 intended for it.

– Adapt the threaded rod 

43

 of the screw clamp to the work-

piece height.

– Firmly tighten the threaded rod 

43

, thus fastening the 

workpiece.

Adjusting the Cutting Angle

To ensure precise cuts, the basic adjustment of the machine 
must be checked and adjusted as necessary after intensive 
use (see “Checking and Adjusting the Basic Adjustment”, 
page 25).



Always tighten the locking knob 23 firmly before saw-
ing. 

Otherwise the saw blade can become wedged in the 

workpiece.

Adjusting Mitre Angles (see figure H)

The mitre angle can be set in the range from 47 ° (left side) to 
47 ° (right side).

– Loosen the locking knob 

23

 in case it is tightened.

– Pull the lever 

24

 and turn the saw table 

20

 until the desired 

mitre angle is indicated on the angle indicator 

22

.

– Tighten the locking knob 

23

 again.

For quick and precise setting of often used mitre angles,

detents 

26

 are provided on the saw table:

– Loosen the locking knob 

23

 in case it is tightened.

– Pull lever 

24

 and rotate the saw table 

20

 left or right to the 

requested detent.

– Release the lever again. The lever must be felt to engage in 

the detent.

Adjusting Bevel Angles (see figure I)

The bevel angle can be set in the range from 0 ° to 45 °.

– Pull the adjustable fence 

4

 completely outward.

– Loosen the lock lever 

8

.

– Tilt the tool arm by the handle 

14

 until the angle indicator 

30

 indicates the desired bevel angle.

– Hold the tool arm in this position and retighten the clamp-

ing lever 

8

.

For quick and precise setting of the standard angles 0 ° 
and 45 °,

 end stops are provided on the housing.

– Pull the adjustable fence 

4

 completely outward.

– Loosen the lock lever 

8

.

– To do so, swivel the tool arm by the handle 

14

 to the stop 

32

 to the right (0 °) or to the stop 

6

 to the left (45 °).

– Retighten the lock lever 

8

 again.

Starting Operation



Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the 
nameplate of the machine. Power tools marked with 
230 V can also be operated with 220 V.

Switching On (see figure J)

To save energy, only switch the power tool on when using it.

– To 

start

 the machine, press the On/Off switch 

13

 and keep 

it pressed.

Note: 

For safety reasons, the On/Off switch 

13

 cannot be 

locked; it must remain pressed during the entire operation.

The tool arm can only be guided downward by pressing lock-
ing switch 

15

.

– For 

sawing

, the locking switch 

15

 must be therefore 

pushed in addition to pressing the On/Off switch 

13

.

Switching Off

– To 

switch off

 the machine, release the On/Off switch 

13

.

Working Advice

General Sawing Instructions



For all cuts, it must first be ensured that the saw blade 
at no time can come in contact with the fence, screw 
clamps or other machine parts. Remove possibly 
mounted auxiliary stops or adjust them accordingly.

Protect the saw blade against impact and shock. Do not sub-
ject the saw blade to lateral pressure.

Do not saw warped/bent workpieces. The workpiece must al-
ways have a straight edge to face against the fence.

Long workpieces must be underlaid or supported at their free 
end.

Left

Right

0 °

45 °

22.5°

15 °

15 °

22.5 °

45 °

OBJ_BUCH-2154-002.book  Page 24  Monday, June 16, 2014  2:55 PM