Bosch 0.601.9C5.000 - Инструкция по эксплуатации - Страница 19

 English | 

19

Bosch Power Tools

1 619 P11 460 | (26.11.13)

Certain dusts, such as oak or beech dust, are considered 
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials 
containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the 
materials to be worked.



Prevent dust accumulation at the workplace. 

Dusts can 

easily ignite.

Operation

Starting Operation

Inserting the battery

– Insert the charged battery 

9

 into the battery port until it 

can be felt to engage and is seated flush.

Switching On and Off

To save energy, only switch the power tool on when using it.

– To 

start

 the power tool, push the On/Off switch 

6

 for-

wards.

– To 

switch off

 the machine, push On/Off switch 

6

 toward 

the rear.

Adjusting the Speed

The speed regulator 

7

 enables continuously variable adjust-

ment of the speed of the power tool even during operation.

– When working with plastics and other materials with a low 

melting point, use low speeds.

– Perform cutting work in wood, iron or steel at high speeds.
– When polishing, buffing and cleaning, work with speeds of 

up to max. 15000 rpm in order to avoid damaging the 
workpiece and application tool.

Working Advice

Detailed work can be carried out best if you hold the power 
tool as a pen between thumb and index finger (see figure F).

For heavy work such as cutting or grinding, use the “golf grip 
method” (see figure G).

Move the cutting disc or grinding accessory with light pres-
sure to achieve an optimum work result. Too much pressure 
will reduce the performance of the power tool and lead to fast-
er wear of the application tool.



Ensure that grinding tools and cutting discs are pro-
tected against impact when stored.

Recommended Cutting Methods

– Panel materials (see figure H)
– Bars  (see figure I)
– Pipes (see figure J)

Blockage protection

The built-in blockage protection protects the motor and bat-
tery in case of a blockage. If the application tool becomes 
jammed in the workpiece or if too much pressure is exerted on 
the workpiece, the motor will stop. 

– Determine the cause of the blockage and correct it.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.



For safe and proper working, always keep the machine 
and ventilation slots clean.

After-sales Service and Application Service

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of 
the machine.

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888

Speed setting

Speed control adjustment

1

5000 – 8000 min

-1

2

9000 – 12000 min

-1

3

16000 – 19000 min

-1

4

20000 – 24000 min

-1

5

24000 – 28000 min

-1

6

30000 – 35000 min

-1

OBJ_BUCH-2020-001.book  Page 19  Tuesday, November 26, 2013  2:57 PM