Bosch PCM 7 S - Инструкция по эксплуатации - Страница 28

28

 | English 

1 609 929 W43 | (22/7/10)

Bosch Power Tools

f

Operate the power tool only when the work 
area to the workpiece is clear of any adjust-
ing tools, wood chips, etc. 

Small pieces of 

wood or other objects that come in contact 
with the rotating saw blade can strike the op-
erator with high speed.

f

Keep the floor free of wood chips and mate-
rial remainders. 

You could slip or trip.

f

Always firmly clamp the piece to be 
worked. Do not saw workpieces that are too 
small to clamp. 

Otherwise, the clearance of 

your hand to the rotating saw blade is too 
small.

f

Use the machine only for cutting the mate-
rials listed under Intended Use. 

Otherwise, 

the machine can be subject to overload.

f

If the saw blade should become jammed, 
switch the machine off and hold the work-
piece until the saw blade comes to a com-
plete stop. To prevent kickback, the work-
piece may not be moved until after the 
machine has come to a complete stop. 

Cor-

rect the cause for the jamming of the saw 
blade before restarting the machine.

f

Do not use dull, cracked, bent or damaged 
saw blades. 

Unsharpened or improperly set 

saw blades produce narrow kerf causing ex-
cessive friction, blade binding and kickback.

f

Always use saw blades with correct size 
and shape (diamond versus round) of arbor 
holes. 

Saw blades that do not match the 

mounting hardware of the saw will run ec-
centrically, causing loss of control.

f

Do not use high speed steel (HSS) saw 
blades. 

Such saw blades can easily break.

f

Do not touch the saw blade after working 
before it has cooled. 

The saw blade be-

comes very hot while working.

f

Never operate the machine without the in-
sert plate. Replace a defective insert plate. 

Without flawless insert plates, injuries are 
possible from the saw blade.

f

Check the cable regularly and have a dam-
aged cable repaired only through an author-
ised customer service agent for Bosch pow-
er tools. Replace damaged extension 
cables. 

This will ensure that the safety of the 

power tool is maintained.

f

Store the machine in a safe manner when 
not being used. The storage location must 
be dry and lockable. 

This prevents the ma-

chine from storage damage, and from being 
operated by untrained persons.

f

Do not direct the laser beam at persons or 
animals and do not stare into the laser 
beam yourself, not even from a distance. 

This power tool produces laser class 2 laser 
radiation according to EN 60825-1. This can 
lead to persons being blinded.

f

Do not replace the installed laser with an-
other laser type. 

A laser that does not fit to 

this power tool could pose dangers for other 
persons.

f

Secure the workpiece. 

A workpiece clamped 

with clamping devices or in a vice is held 
more secure than by hand.

f

Never leave the machine before it has come 
to a complete stop. 

Cutting tools that are 

still running can cause injuries.

f

Never use the machine with a damaged ca-
ble. Do not touch the damaged cable and 
pull the mains plug when the cable is dam-
aged while working. 

Damaged cables in-

crease the risk of an electric shock.

Products sold in GB only

: Your product is fitted 

with an BS 1363/A approved electric plug with 
internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, 
it should be cut off and an appropriate plug fit-
ted in its place by an authorised customer serv-
ice agent. The replacement plug should have the 
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a 
possible shock hazard and should never be in-
serted into a mains socket elsewhere.

Products sold in AUS and NZ only

: Use a resid-

ual current device (RCD) with a rated residual 
current of 30 mA or less.

OBJ_BUCH-1270-001.book  Page 28  Thursday, July 22, 2010  12:44 PM