Zelmer 616 - Инструкция по эксплуатации - Страница 124

124

Wait until the steam cleaning indicator (

–

4

) lights up again (indicating that the appliance is ready to 

work) and turn on the steam exhaust switch (

3

).

ATTENTION!!!  To avoid cracks on windows, mirrors and other glass surfaces located in cold 

(non-heated) rooms and resulting from too big difference of temperature, 

fi

 rst heat 

these surfaces with a small amount of steam and then begin standard cleaning.

Press the button on the hose grip to adjust the water in

fl

 ow to the nozzle.

–

The presence of water at the end of the nozzle while starting the stem 
cleaning mode is typical.

Move the nozzle on the cleaned area back and forth. The time and intensity of 

–

cleaning depends on the amount of dirt and the type of the background.
The amount of water in the rear container may be not enough to clean the entire area. Therefore, when 

–

all water in the container is used up, re

fi

 ll the container, switch on the wet cleaning (detergent) mode 

and switch it back to the steam cleaning mode when water appears on the nozzle outlet.
Upon cleaning a part of the 

fl

 oor, stop spraying, turn the vacuum cleaner on and suck in the liquid 

–

created by condensing steam. To do this move the nozzle slowly towards you until the liquid is removed 
from the 

fl

 oor. Repeat this operation until the entire surface is cleaned and dries up.

If the three-position switch (1) is set to "1” (steam cleaning) and you want to change it to the “wet 
cleaning” mode (“2”), you have to move the switch to the neutral “0” 

fi

 rst and then to “2”. Never 

switch the three-position switch from “1” to “2” directly.
ATTENTION!!!  Never switch the three-position switch from „1” to „2” directly with the omission 

of the neutral “0”.

Once you have completed spraying turn off the pump (set the three-position switch (

–

1

) to “

0

” – the 

picture on p.3) and press the button on the hose grip to adjust the water 

fl

 ow to the nozzle to “release 

the pressure”.

Preparation of the vacuum cleaner for steam cleaning

To prepare a saline solution use 3.5l of demineralized (distilled) water with 5g of table salt (1/2 level 
teaspoon) or 5 ml of physiological salt (available in drugstores). Do not use salt every time. Use salt to 
every third-

fi

 fth water tank.

Do not add salt to tap water.

ATTENTION!!!  It is much better to use pure (distilled) water to prevent build-up of scale in the 

steam generator.

Put the inlet cap into the slot on the rear container.

–

Set the container in place and press it to 

fi

 x it 

fi

 rmly to the body.

–

close the upper cover.

–

ATTENTION!!! 

DO NOT LEAVE THE APPLIANCE READY TO CLEAN (THE STEAM GENERATOR IS 
ON) FOR MORE THAN 30 MINUTES.

STEAM CLEANING SMOOTH SURFACES

To use the vacuum cleaner for steam cleaning the glaze, windows, mirrors and other glass surfaces you 
should:

attach the steam spray nozzle on the detergent/steam 

–

extension pipe and lock this joint by turning the blockade,
depending on the amount of dirt 

fi

 x the proper insert 

–

(collecting or cleaning) to the nozzle.

Set the three-position (

–

1

) switch to“

1

”.

Wait until the steam cleaning indicator (

–

4

) is on and turn 

on the steam exhaust switch (

3

) for 5 seconds, which will 

then light up.The pressure inside the steam generator 
will be released.
After this time turn the switch off.

–

instrukcja 616-010.indb   124

instrukcja 616-010.indb   124

2008-09-18   16:03:20

2008-09-18   16:03:20