Bosch AKE 35-19 S - Инструкция по эксплуатации - Страница 19

 English | 

19

Bosch Power Tools

F 016 L81 142 | (7.12.16)

Power tool use and care



Do not force the power tool. Use the correct power tool 
for your application. 

The correct power tool will do the 

job better and safer at the rate for which it was designed.



Do not use the power tool if the switch does not turn it 
on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.



Disconnect the plug from the power source and/or the 
battery pack from the power tool before making any 
adjustments, changing accessories, or storing power 
tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.



Store idle power tools out of the reach of children and 
do not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other 
condition that may affect the power tool’s operation. If 
damaged, have the power tool repaired before use. 

Many accidents are caused by poorly maintained power 
tools.



Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 
and are easier to control.



Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account 
the working conditions and the work to be performed. 

Use of the power tool for operations different from those 
intended could result in a hazardous situation.

Service



Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Chain Saw Safety Warnings



Keep all parts of the body away from the saw chain 
when the motor is operating. Before you start the chain 
saw, make sure the saw chain is not contacting any-
thing. 

A moment of inattention while operating chain saws 

may cause entanglement of your clothing or body with the 
saw chain.



Always hold the chain saw with your right hand on the 
rear handle and your left hand on the front handle. 

Holding the chain saw with a reversed hand configuration 
increases the risk of personal injury and should never be 
done.



Hold the power tool by insulated gripping surfaces on-
ly, because the saw chain may contact hidden wiring or 
its own cord. 

Saw chains contacting a “live” wire may 

make exposed metal parts of the power tool “live” and 
could give the operator an electric shock.



Wear safety glasses and hearing protection. Further 
protective equipment for head, hands, legs and feet is 
recommended. 

Adequate protective clothing will reduce 

personal injury by flying debris or accidental contact with 
the saw chain.



Do not operate a chain saw in a tree. 

Operation of a chain 

saw while up in a tree may result in personal injury.



Always keep proper footing and operate the chain saw 
only when standing on fixed, secure and level surface. 

Slippery or unstable surfaces such as ladders may cause a 
loss of balance or control of the chain saw.



When cutting a limb that is under tension be alert for 
spring back. 

When the tension in the wood fibres is re-

leased the spring loaded limb may strike the operator 
and/or throw the chain saw out of control.



Use extreme caution when cutting brush and saplings. 

The slender material may catch the saw chain and be 
whipped toward you or pull you off balance.



Carry the chain saw by the front handle with the chain 
saw switched off and away from your body. When 
transporting or storing the chain saw, always fit the 
guide bar cover. 

Proper handling of the chain saw will re-

duce the likelihood of accidental contact with the moving 
saw chain.



Follow instructions for lubricating, chain tensioning 
and changing accessories. 

Improperly tensioned or lubri-

cated chain may either break or increase the chance for 
kickback.



Keep handles dry, clean, and free from oil and grease. 

Greasy, oily handles are slippery causing loss of control.



Cut wood only. Don’t use chain saw for purposes not in-
tended. For example: do not use chain saw for cutting 
plastic, masonry or non-wood building materials. 

Use of 

the chain saw for operations different than intended could 
result in a hazardous situation.



Causes and operator prevention of kickback: 

–  Kickback may occur when the nose or tip of the guide bar 

touches an object, or when the wood closes in and pinches 
the saw chain in the cut.

–  Tip contact in some cases may cause a sudden reverse 

reaction, kicking the guide bar up and back towards the op-
erator.

–  Pinching the saw chain along the top of the guide bar 

may push the guide bar rapidly back towards the operator.

–  Either of these reactions may cause you to lose control of 

the saw which could result in serious personal injury. Do 
not rely exclusively upon the safety devices built into your 
saw. As a chain saw user, you should take several steps to 
keep your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect oper-
ating procedures or conditions and can be avoided by tak-
ing proper precautions as given below:



Maintain a firm grip, with thumbs and fingers encir-
cling the chain saw handles, with both hands on the saw 
and position your body and arm to allow you to resist 
kickback forces. 

Kickback forces can be controlled by the 

operator, if proper precautions are taken. Do not let go of 
the chain saw.



Do not overreach and do not cut above shoulder height. 

This helps prevent unintended tip contact and enables bet-
ter control of the chain saw in unexpected situations.

OBJ_BUCH-1238-002.book  Page 19  Wednesday, December 7, 2016  2:54 PM