Yamaha RX-V2065 - Инструкция по эксплуатации - Страница 64

62

 En

Controlling other components with the remote control

You can program remote control codes from other remote 
controls. Use this feature if you want to program functions 
not included in the basic operations covered by the remote 
control codes, or an appropriate remote control code is not 
available.

Note

<Note>

•

Each of the steps described in this section should be performed within 
one minute after the last step. If the next operation is not performed 
within one minute, the programming operation is canceled. In this case, 
start again from the beginning.

You can program the remote control to make functions of 
an external component operable with the following keys. 
You can assign functions to these keys for each input 
source as with remote control codes.

c

SOURCE POWER

k

External component operation keys

l

Numeric keys

y

•

The remote control transmits infrared rays. If the remote control of the 
external component also uses infrared rays, this remote control can learn 
most of its functions. The remote control may not recognize special or 
consecutive signals.

•

The keys may not operate the assigned functions depending on operating 
conditions of this unit.

1

Press 

o

CODE SET

 on the remote control 

using a pointed object such as the tip of a 
ballpoint pen.

n

TRANSMIT

 blinks twice.

2

Press the desired 

d

Input selection key

.

3

Press 

l

Numeric keys

 to enter “9990”.

4

Press a key to which you want to assign the 
function.

n

TRANSMIT

 lights up and this unit enters a wait 

state to receive remote control signals. Perform steps 
5 and 6 within 10 seconds.

Note

<Note>

•

If 10 seconds pass after this unit enters the wait state, a timeout 
error occurs and 

n

TRANSMIT

 turns off. In this case, repeat 

from step 4.

5

Place the remote control about 5 to 10 cm 
apart from the remote control of the external 
component on a flat surface so that their 
infrared transmitters are aimed at each other.

6

Press the key on the remote control of the 
external component.

If the learning process is complete, 

n

TRANSMIT

blinks twice. If it fails, 

n

TRANSMIT

 blinks six 

times. Repeat from step 4.

y

•

Repeat steps 4 thorough 6 to assign a function to another key.

7

To end the operation, press 

o

CODE SET

again.

n

TRANSMIT

 blinks once.

1

Press 

o

CODE SET

 on the remote control 

using a pointed object such as the tip of a 
ballpoint pen.

n

TRANSMIT

 blinks twice.

2

Press the desired 

d

Input selection key

.

3

Press 

l

Numeric keys

 to enter “9991”.

4

Press a key you want to reset.

If the key assignment is cleared, 

n

TRANSMIT

blinks twice. If it fails, 

n

TRANSMIT

 blinks six 

times. Repeat from step 1.

y

•

Repeat step 4 to clear another key assignment.

5

To end the operation, press 

o

CODE SET

again.

n

TRANSMIT

 blinks once.

1

Press 

o

CODE SET

 on the remote control 

using a pointed object such as the tip of a 
ballpoint pen.

n

TRANSMIT

 blinks twice.

2

Press the desired 

d

Input selection key

.

3

Press 

l

Numeric keys

 to enter “9992”.

If the key assignments are cleared, 

n

TRANSMIT

blinks twice. If it fails, 

n

TRANSMIT

 blinks six 

times. Repeat from step 1.

Programming from other remote 
controls

Programming the remote control of this unit

BD

DV
D

TV

CD

RADIO

SLEEP

FM

AM

INFO

MEMOR

Y

1

2

3

4

1

2

3

4

5

6

1

2

PHONO

MUL

TI

DOCK

TUNER

V-

A

U

X

HDMI

MUSIC

STEREO

ENHANCER

SUR.

 DECODE

MO

VIE

STRAIGHT

HDMI OUT

PURE DIRECT

USB/NET

PRESET

TUNING

ON SCREEN

OPTION

SOURCE

PO

WER

SCENE

RETURN

ENTER

V

O

LUME

DISPLA

Y

HDMI

AU

D
IO

TRANSMIT

CODE SET

MAIN

ZONE 2

ZONE 3

AV

PO

WER

5 to 10 cm 

Remote control of external component

Clearing the assignment of each key

Clearing the assignments of all keys