Bosch GWS 22 230 JH 0601882203 - Инструкция по эксплуатации - Страница 15

16

 | English 

1 609 929 X88 | (8.2.12)

Bosch Power Tools

f

Do not overreach. Keep proper footing and balance at 

all times. 

This enables better control of the power tool in 

unexpected situations.

f

Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from 

moving parts. 

Loose clothes, jewellery or long hair can be 

caught in moving parts.

f

If devices are provided for the connection of dust ex-

traction and collection facilities, ensure these are con-

nected and properly used. 

Use of dust collection can re-

duce dust-related hazards.

Power tool use and care

f

Do not force the power tool. Use the correct power tool 

for your application. 

The correct power tool will do the 

job better and safer at the rate for which it was designed.

f

Do not use the power tool if the switch does not turn it 

on and off. 

Any power tool that cannot be controlled with 

the switch is dangerous and must be repaired.

f

Disconnect the plug from the power source and/or the 

battery pack from the power tool before making any 

adjustments, changing accessories, or storing power 

tools. 

Such preventive safety measures reduce the risk of 

starting the power tool accidentally.

f

Store idle power tools out of the reach of children and 

do not allow persons unfamiliar with the power tool or 

these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.

f

Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other 

condition that may affect the power tool’s operation. If 

damaged, have the power tool repaired before use. 

Many accidents are caused by poorly maintained power 

tools.

f

Keep cutting tools sharp and clean. 

Properly maintained 

cutting tools with sharp cutting edges are less likely to bind 

and are easier to control.

f

Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account 

the working conditions and the work to be performed. 

Use of the power tool for operations different from those 

intended could result in a hazardous situation.

Service

f

Have your power tool serviced by a qualified repair per-

son using only identical replacement parts. 

This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Angle Grinder

Safety Warnings common for Grinding, Sanding, Wire 

Brushing or Abrasive Cutting Off Operations

f

This power tool is intended to function as a grinder, 

sander, wire brush or cut-off tool. Read all safety warn-

ings, instructions, illustrations and specifications pro-

vided with this power tool. 

Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or 

serious injury.

f

This power tool is not recommended for polishing. 

Op-

erations for which the power tool was not designed may 

create a hazard and cause personal injury.

f

Do not use accessories which are not specifically de-

signed and recommended by the tool manufacturer. 

Just because the accessory can be attached to your power 

tool, it does not assure safe operation.

f

The rated speed of the accessory must be at least equal 

to the maximum speed marked on the power tool. 

Ac-

cessories running faster than their rated speed can break 

and fly apart.

f

The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power 

tool. 

Incorrectly sized accessories cannot be adequately 

guarded or controlled.

f

The arbor size of wheels, flanges, backing pads or any 

other accessory must properly fit the spindle of the 

power tool. 

Accessories with arbor holes that do not 

match the mounting hardware of the power tool will run out 

of balance, vibrate excessively and may cause loss of con-

trol.

f

Do not use a damaged accessory. Before each use in-

spect the accessory such as abrasive wheels for chips 

and cracks, backing pad for cracks, tear or excess 

wear, wire brush for loose or cracked wires. If power 

tool or accessory is dropped, inspect for damage or in-

stall an undamaged accessory. After inspecting and in-

stalling an accessory, position yourself and bystanders 

away from the plane of the rotating accessory and run 

the power tool at maximum no-load speed for one 

minute. 

Damaged accessories will normally break apart 

during this test time.

f

Wear personal protective equipment. Depending on 

application, use face shield, safety goggles or safety 

glasses. As appropriate, wear dust mask, hearing pro-

tectors, gloves and workshop apron capable of stop-

ping small abrasive or workpiece fragments. 

The eye 

protection must be capable of stopping flying debris gen-

erated by various operations. The dust mask or respirator 

must be capable of filtrating particles generated by your 

operation. Prolonged exposure to high intensity noise may 

cause hearing loss.

f

Keep bystanders a safe distance away from work area. 

Anyone entering the work area must wear personal 

protective equipment. 

Fragments of workpiece or of a 

broken accessory may fly away and cause injury beyond 

immediate area of operation.

f

Hold the power tool by insulated gripping surfaces on-

ly, when performing an operation where the cutting ac-

cessory may contact hidden wiring or its own cord. 

Cut-

ting accessory contacting a “live” wire may make exposed 

metal parts of the power tool “live” and could give the op-

erator an electric shock.

f

Position the cord clear of the spinning accessory. 

If you 

lose control of the power tool, the cord may be cut or 

snagged and your hand or arm may be pulled into the spin-

ning accessory.

OBJ_BUCH-777-008.book  Page 16  Wednesday, February 8, 2012  8:04 AM