Bosch 18V-10 solo (0.601.9J4.002) - Инструкция по эксплуатации - Страница 37

English | 

37

The power tool must always work in an
up-grinding motion. Otherwise there
is a risk that it will be pushed 

uncon-

trolled

 out of the cut. For best results

when cutting profiles and rectangular
tubing, start at the smallest cross sec-
tion.

Cutting stone

u

For cutting stone with bonded cutting discs or dia-
mond cutting discs for concrete/stone, always use the
extraction guard for cutting with a cutting guide

(29)

or the protective guard for cutting

(16) or the protect-

ive guard for grinding

(15)

with a fitted cover for

cutting

(17)

.

u

Provide sufficient dust extraction when cutting stone.

u

Wear a dust mask.

u

The power tool may be used only for dry cutting/grind-
ing.

u

When using the protective guard for cutting

(16)

, the

protective guard for grinding

(15)

 or the protective

guard for grinding

(15)

 with a fitted cover for

cutting

(17)

 for cutting and grinding applications in

concrete or masonry, there is an increased dust load
and an increased risk of losing control of the power
tool, which can lead to kickback.

For cutting stone, it is best to use a diamond cutting disc.
When using the extraction guard for cutting with a cutting
guide 

(29)

, the dust extractor must be approved for extract-

ing stone dust. Suitable dust extractors are available from
Bosch.

Switch on the power tool and position
it with the front part of the cutting
guide on the workpiece. Move the
power tool with a moderate feed mo-
tion that is suited to the material being
machined.

When cutting especially hard materials such as concrete
with a high pebble content, the diamond cutting disc can
overheat and become damaged as a result. This is clearly in-
dicated by circular sparking, rotating with the diamond cut-
ting disc.
If this happens, stop cutting and allow the diamond cutting
disc to cool down by running the power tool for a short time
at maximum speed with no load.
If work is noticeably slower and with circular sparking, this
indicates that the diamond cutting disc has become blunt.
You can resharpen the disc by briefly cutting into abrasive
material (e.g. lime-sand brick).

Cutting other materials

u

For cutting materials such as plastic, composite ma-
terials, etc. with bonded cutting discs or Carbide Multi
Wheel cutting discs, always use the protective guard
for cutting

(16)

or the protective guard for

grinding

(15)

with a fitted cover for cutting 

(17). You

can achieve improved dust extraction

by using the ex-

traction guard with a cutting guide

(29)

.

Working with Diamond Annular Cutters

u

Only use dry diamond annular cutters.

u

Always fit the hand guard (28) when working with dia-
mond annular cutters.

Do not place the diamond annular cutter parallel to the work-
piece. Plunge it into the workpiece at an angle and in a circu-
lar motion. This will allow you to achieve optimal cooling and
ensure a longer tool life for the diamond annular cutter.

Information on structural design

Recesses in load-bearing walls are subject to country-spe-
cific regulations. These regulations must be observed under
all circumstances. Seek advice from the responsible struc-
tural engineer, architect or construction supervisor before
starting work.

Start-Up

Switching on/off
(GWS 18V-10 / GWS 18V-10 SC)

To 

start

 the power tool, push the on/off switch 

(6)

 forward.

To 

lock

 the on/off switch 

(6)

 in position, push the on/off

switch 

(6)

 forward and down until it clicks into place.

To 

switch off

 the power tool, release the on/off switch 

(6)

;

or, if the switch is locked, briefly push the on/off switch 

(6)

backward and down and then release it.

u

Always check abrasive tools before using them. The
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use.

 Damaged

abrasive tools can burst apart and cause injuries.

Switching On/Off
(GWS 18V-10 PC / GWS 18V-10 PSC)

To 

start

 the power tool, push the unlocking lever 

(13)

 for-

wards and then push the on/off switch 

(12)

 up.

To 

switch off

 the power tool, release the on/off switch 

(12)

.

u

Always check abrasive tools before using them. The
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use.

 Damaged

abrasive tools can burst apart and cause injuries.

Bosch Power Tools

1 609 92A 769 | (13.02.2023)