Bosch 18V-10 solo (0.601.9J4.002) - Инструкция по эксплуатации - Страница 26

26

 | English

u

Do not use a damaged accessory. Before each use in-
spect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess
wear, wire brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for damage or in-
stall an undamaged accessory. After inspecting and
installing an accessory, position yourself and bystand-
ers away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one
minute. 

Damaged accessories will normally break apart

during this test time.

u

Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments. 

The eye

protection must be capable of stopping flying debris gen-
erated by various applications. The dust mask or respir-
ator must be capable of filtrating particles generated by
the particular application. Prolonged exposure to high in-
tensity noise may cause hearing loss.

u

Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. 

Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond
immediate area of operation.

u

Hold the power tool by insulated gripping surfaces
only, when performing an operation where the cutting
tool may contact hidden wiring.

 Contact with a "live"

wire will also make exposed metal parts of the power tool
"live" and could give the operator an electric shock.

u

Never lay the power tool down until the accessory has
come to a complete stop. 

The spinning accessory may

grab the surface and pull the power tool out of your con-
trol.

u

Do not run the power tool while carrying it at your
side.

 Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into your
body.

u

Regularly clean the power tool’s air vents.

 The motor’s

fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.

u

Do not operate the power tool near flammable materi-
als.

 Sparks could ignite these materials.

u

Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in electro-
cution or shock.

Kickback and related warnings:

Kickback is a sudden reaction to a pinched or snagged rotat-
ing wheel, backing pad, brush or any other accessory. Pinch-
ing or snagging causes rapid stalling of the rotating access-
ory which in turn causes the uncontrolled power tool to be
forced in the direction opposite of the accessory’s rotation
at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either
jump toward or away from the operator, depending on direc-
tion of the wheel’s movement at the point of pinching. Abras-
ive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.

u

Maintain a firm grip with both hands on the power tool
and position your body and arms to allow you to resist
kickback forces. Always use auxiliary handle, if
provided, for maximum control over kickback or
torque reaction during start-up. 

The operator can con-

trol torque reactions or kickback forces, if proper precau-
tions are taken.

u

Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

u

Do not position your body in the area where power
tool will move if kickback occurs. 

 Kickback will propel

the tool in direction opposite to the wheel’s movement at
the point of snagging.

u

Use special care when working corners, sharp edges,
etc. Avoid bouncing and snagging the accessory. 

Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.

u

Do not attach a saw chain woodcarving blade, seg-
mented diamond wheel with a peripheral gap greater
than 10 mm or toothed saw blade. 

Such blades create

frequent kickback and loss of control.

Safety warnings specific for grinding and cutting-off
operations:

u

Use only wheel types that are specified for your power
tool and the specific guard designed for the selected
wheel. 

Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

u

The grinding surface of centre depressed wheels must
be mounted below the plane of the guard lip. 

 An im-

properly mounted wheel that projects through the plane
of the guard lip cannot be adequately protected.

u

The guard must be securely attached to the power tool
and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator. 

The guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel and
sparks that could ignite clothing.

u

Wheels must be used only for specified applications.
For example: do not grind with the side of cut-off
wheel. 

Abrasive cut-off wheels are intended for peri-

pheral grinding, side forces applied to these wheels may
cause them to shatter.

u

Always use undamaged wheel flanges that are of cor-
rect size and shape for your selected wheel. 

 Proper

wheel flanges support the wheel thus reducing the pos-
sibility of wheel breakage. Flanges for cut-off wheels may
be different from grinding wheel flanges.

1 609 92A 769 | (13.02.2023)

Bosch Power Tools