котёл Baxi SLIM HPS 1.80 A7114600 - Инструкция по эксплуатации - Страница 58

TO TURN ON THE HEATING

– Turn on the main switch.
– Set the correct hour of the day and the day of the week.
– Place in automatic mode with the button

.

TO SET THE HOUR

HOW TO USE THE AUTOMATIC MODE

In the automatic mode the temperature of the room is regu-
lated on the basis of the periods of heating chosen.

– Push the button

.

NOTE: Select the heating periods according to one’s daily
requirements; in this way  it is possible to significantly
save on energy.

TO ACTIVATE CONTINUOUS HEATING

The continuous heating mode keeps the temperature of the
room at the set level via the regulating knob.

– Push the “Continuous Operation” button

.

– Regulate the room temperature with the 

regulating knob.

TO SET THE STANDBY MODE
(when the user is away for a long period of time)

The standby mode keeps the temperature of the room at
the level of antifreeze protection.

– Push the “Standby mode” button

.

MEANING OF THE SYMBOLS

On the display a few of the symbols indicate the current ope-
rating state. The appearance of a line under one of these
symbols signals that the corresponding operating state is
“active”.

Heating at the nominal temperature 
(regulating knob)

Heating at reduced temperature (line

).

Heating at antifrost protection temperature 
(line

).

NOTE: For further information on the symbols and the
operating state refer to the detailed description of the
heating plant.

TO VARY THE HOT WATER PRODUCTION

The production of hot water can be activated or deactivated
by the push of a button.

– Push the button “Hot water”

.

IF THE HOT WATER IS TOO HOT OR TOO COLD

IF THE ROOMS ARE TOO HOT OR TOO COLD

– Check that current operating state on the display.
– In the case of 

nominal temperature

.

Increase or reduce the temperature of the room with the
regulating knob.

– In the case of 

reduced temperature

.

NOTE: After each regulation wait at least two hours for
the new temperature to expand through the room.

TO CHANGE THE HEATING PERIODS

With reference to the day chosen set the changes
as following:

NOTE: The heating periods automatically repeat on a
weekly basis. 
To this end select the automatic mode.
It is possible to reset the standard programme on line 23
by pushing the buttons + and – at the same time.

IF THE HEATING DOES NOT WORK PROPERLY

– Refer to the detailed documentation 

on the heating system, following the fault finding 
instructions.

TO MEASURE GAS COMBUSTION

– Push the “chimneysweep” button 

.

The heating will work according to the level requested.

HOW TO SAVE ENERGY WITHOUT FOREGOING ON COMFORT

– A temperature of around 21°C is advised in the rooms

that are used. Every degree above this will increase hea-
ting costs by 6–7%.

– Aerate the rooms only for a brief period, opening the win-

dows completely.

– In the rooms that are not used place the regulating valve

in the antifreeze position.

– Leave the space in front of the radiators free from

obstructions (remove furniture, curtains...).

– Close windows and blinds to reduce 

dispersion of heat.

Select the

Display

Set the regulation

line

with the buttons

hour of the day

day of the week

1

2

14

15

Select the

Display

Pre-select the weekly block

line

or the single day

1-7 = week

1 = Lu/7 = Do

5

Period

Push

Display

Set

For

requested

button

hour

°C

Start

End

Start

End

Start

End

6

7

8

9

10

11

Select the

Display

Change the temperature

line

with the buttons

°C

14

P

e

riod 1

P

e

riod 2

P

e

riod 3

13

Select the

Display

Set the desired

line

temperature

°C

58

CONTROL SYSTEM

In order to get the highest potential out of the 

“RVA 43.222”

regulator follow the instructions given below: