Clatronic ES 2968 - Инструкция по эксплуатации - Страница 41

E

N

G

LI

S

H

E

N

G

LI

S

H

ENGLISH

41

Troubleshooting

Malfunction Possible 

Causes

Remedy 

When the 
function se-
lector switch 
is operated 
the device 
does not 
switch on.

The device has no 
power supply. 

Check the socket with 
another device and 
insert the mains plug 
correctly.

Coffee stops 
fl owing.

The water tank is 
empty.

Switch off the device 
and fi ll up the water 
tank. 

The tank is not 
correctly inserted, the 
valve is not open.

Press the tank down 
slightly so that the 
valve opens. 

The holes in the fi lter 
holder and the outlet 
on the brewing head 
are blocked.

Clean the fi lter holder, 
the fi lter and the 
outlet on the brewing 
head.

Air has entered the 
„heating element“. 

Produce some steam 
(see the section 
„Preparing Cappuc-
cino“) and turn the 
steam regulator to the 
highest level.

Coffee is too fi ne or 
pressed too fi rm

.

Loosen the coffee 
powder.

Scale has accumu-
lated in the espresso 
machine.

The appliance needs 
de-scaling

.

The pump 
makes loud 
noises. 

Water tank is empty

Switch off the 

device and fi ll up the 
container.

There is air in the 
water system.

Fill the water tank 
and remove air from 
the machine (see the 
section „Initial Use/Air 
Removal“).

The tank is not 
inserted correctly, the 
valve is not open.

Press the tank down 
lightly so that the 
valve opens. 

The espresso 
comes out 
of the edge 
of the fi lter 
holder. 

The Filter is in the 
wrong position or 
is not closed fi rm 
enough. 

Remove the fi lter than 
refi t or switch off the 
machine and tighten 
the fi lter

.

Coffee is on the 
rubber gasket.

Please wipe off

.

Too much coffee in 
the fi lter

.

Remove any excess 
coffee powder.

Malfunction Possible 

Causes

Remedy 

The espresso 
coffee is too 
cold.

The cups were not 
warmed beforehand.

Rinse out the cups 
with hot water. 

The heating up 
phase had not been 
completed. 

Please wait for the 
heating up phase to 
fi nish.

During preparation 
of the coffee the „
/ 

“ lamp has not 

yet gone on.

Please wait until the 
control lamp lights up.

The coffee 
has a slightly 
acidic taste. 

The espresso was 
not fresh

.

The coffee 
foam is slight-
ly discoloured 
(the coffee 
fl ows out 
quickly).

Coffee too coarse 
or not pressed fi rm 
enough

.

Use the tamper.

There is not enough 
coffee in the fi lter

.

Fill in more coffee 
powder.

The coffee 
foam is a dark 
colour (the 
coffee only 
fl ows out 
slowly).

Coffee too fi ne or 
pressed to fi rm

.

Loosen the coffee 
powder.

Too much coffee in 
the fi lter

.

Remove any excess 
coffee powder.

The coffee is 
not creamy 
enough. 

The adapter is not 
correctly inserted.

Insert the adapter 
correctly. 

The second sealing 
ring in the fi lter 
holder is not correctly 
inserted.

Insert the ring 
correctly. 

Wrong coffee was 
used

Change the brand if 
necessary.

The milk is not 
foamed up.

The milk used is not 
suitable.

Check the fat content. 
Use low-fat milk.

The milk is not cold 
enough.

Use cooled milk.

The steam nozzle 
is dirty. 

Clean the steam 
nozzle. 

Technical Data

Model: ..............................................................................ES 2968

Power supply: ............................................................ 230 V, 50 Hz

Power consumption:...........................................................1150 W

Protection class: ...........................................................................

Ι

Pressure: ..............................................................................15 bar

This device has been tested according to all relevant current 
CE guidelines, such as electromagnetic compatibility and low 
voltage directives, and has been constructed in accordance with 
the latest safety regulations. 

Subject to technical changes without prior notice!

05-ES 2968 ProfiCook NEW   41

07.04.2006, 10:01:13 Uhr

Downloaded from CoffeeMachineManual.com Manuals