Clatronic ES 2968 - Инструкция по эксплуатации - Страница 40

E

N

G

LI

S

H

ENGLISH

40

Making a Cappuccino

To make a cappuccino, you must fi rst make an espresso. 
Proceed as described under “Making an Espresso” from steps 1 
to 15. To froth the milk, proceed as follows:

1.  Make sure that the function selector (5) is in 

O

 position.

2.  Swing the steam nozzle (10) out so that you can position the 

container (please use a heat-resistant container) comfortab-
ly under the nozzle.

3.  Fill the container up to a 1/3 with fresh cold milk (warm, hot 

or stale milk does not froth). You will produce more stable 
foam if you use low-fat milk.

4.  Turn the function selector switch to „ “. The „ “ and 

„

“ control lamps light up. Wait until the „

/

“ 

control lamp lights up. The device is now ready for foaming.

5.  Immerse the steam nozzle into the vessel just under the 

surface of the milk.

6.  Now set the desired steam quantity by carefully turning the 

steam regulator (3) and moving the collection vessel gently 
up and down. Once the milk reaches the desired volume, 
you can warm the milk more by lowering the steam nozzle 
(10) to the bottom of the container. Do not make the milk boil 
or the froth will be ruined.

7.  Turn the function selector switch (5) back to the 

O 

position; 

the device is now switched off.

8.  Scoop out the froth into the espresso. Add liquid milk. A 

cappuccino is usually composed of 1/3 coffee, 1/3 hot milk 
and 1/3 frothed milk.

Your cappuccino is now ready. Improve the fl avor by adding 
some cinnamon or chocolate powder.

Cleaning

• 

Before cleaning the device please turn the function 
selector switch to „O“ and remove the mains plug from 
the socket.

•  Before cleaning the machine please wait until it has cooled 

down.

•  The water tank, the drip tray, the drip tray cover of the fi lters 

and the fi lter holder can be cleaned by hand in warm soapy 
water. Do not use abrasive detergents. Rinse the parts 
regularly.

•  If the fi lter’s holes are clogged, clean it with a fi ne brush.
•  Never immerse the device in water or other liquids. 
•  Never wash the parts or accessories in a dishwasher. The 

drip tray has an overfl ow protection. A red-marked “fl oat” (8) 
is found in the tray. The more water the drip tray contains, 
the higher the fl oat rises. To empty the tray you can remove 
the drip tray completely and lift the grid.

•  After frothing milk, the steam nozzle is to be immediately 

cleaned from all milk residues.

•  If the milk dries, it becomes diffi cult to remove. To do so, 

dismantle the steam nozzle. Turn the joint above the steam 
nozzle through a quarter turn to the left and remove the 
upper section and the internal pipe (see device overview). 
Soak the steam tube in a container with water over night 
so that the milk residue softens. Place a heat-resistant 
container full of water under the nozzle so that the nozzle is 
dipped in the water. Then turn the function selector switch to 
the   position and produce some steam, as described un-
der “Preparing Cappuccino”. Then turn the function selector 
switch back to 

O

. Wipe the steam nozzle with a moist cloth 

to remove the milk residue before it hardens.

Descaling 

•  This appliance should be de-scaled on a regular basis, 

depending on the frequency of use and the quality of your 
water (i.e. hardness, mineral contents). 

Please note: 

Use solemnly products recommended for 

household percolators. Please use the product according to 
its description.

•  Use the appliance as described under “making espresso” 

until the tank is empty. Allow half of the solution to run 
through the brew head (without coffee and fi lter) and the 
remaining half trough the steam valve.

•  Rinse the tank refi ll it and let 2 – 3 tanks of fresh cold water 

run through the system until you all odours of the de-scaling 
product have vanished.

05-ES 2968 ProfiCook NEW   40

07.04.2006, 10:01:11 Uhr

Downloaded from CoffeeMachineManual.com Manuals