Триммеры Ryobi RBC430SBSD 5133002548 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
29
English (original instructions)
EN
FR
DE
ES
IT
PT
NL
SV
DA
NO
FI
HU
CS
RU
RO
PL
SL
HR
ET
LT
LV
SK
BG
for best performance.
Q
Stop the engine and disconnect the spark plug lead.
Q
Gather two of the pre-cut lengths of trimmer line
provided or cut two pieces of trimmer line, in 28cm
lengths.
Q
Insert the line into the slots located on the sides
of the line head. Line should be pushed in until
approximately 2.5cm protrudes from the holes on the
top of the line head.
Q
Remove old line by pulling it from the holes located
on the top of the line head.
Q
CLEANING THE EXHAUST PORT, SILENCER AND
SPARK ARRESTOR
NOTE:
Depending on the type of fuel used, the type
and amount of lubricant used, and/or your operating
conditions, the exhaust port, silencer, and/or spark
a r r e s t o r s c r e e n m a y b e c o m e b l o c k e d w i t h c a r b o n
deposits. If you notice a power loss with your petrol
powered tool, you may need to remove these deposits
to restore performance. We highly recommend that only
qualified service technicians perform this service.
The spark arrestor must be cleaned or replaced every
50 hours or yearly to ensure proper performance of your
product. Spark arrestors may be in different locations
depending on the model purchased. Please contact
your nearest service dealer for the location of the spark
arrestor for your model.
IDLE SPEED ADJUSTMENT
See Figure 14 for RBC430SBS
See Figure 15 for RBC430SES
If the cutting attachment turns at idle, the idle speed
screw needs adjusting on the engine. Turn the idle speed
screw counter clockwise to reduce the idle RPM and
stop the cutting attachment movement. If the cutting
attachment still moves at idle speed, contact a service
dealer for adjustment and discontinue use until the repair
is made.
WARNING:
The cutting attachment should never turn at idle.
Turn the idle speed screw counter clockwise
to reduce the idle RPM and stop the cutting
a t t a c h m e n t , o r c o n t a c t a s e r v i c e d e a l e r f o r
adjustment and discontinue use until the repair
is made. Serious personal injury may result from
the cutting attachment turning at idle.
CLEANING AIR FILTER SCREEN
See Figure 15, 19. for RBC430SBS
See Figure 16, 21. for RBC430SES
Q
For proper performance and long life, keep air filter
screen clean.
Q
Remove the air filter cover by pushing down on the
latch with your thumb while gently pulling on the
cover.
Q
Brush the air filter screen lightly to clean.
Q
Replace the air filter cover by inserting the tabs on
the bottom of the cover into the slots on the air filter
base; push the cover up until it latches securely in
place.
FUEL CAP
WARNING:
A leaking fuel cap is a fire hazard and must be
replaced immediately.
CE
The fuel cap contains a non-serviceable filter and a
check valve. A clogged fuel filter will cause poor engine
performance. If performance improves when the fuel cap
is loosened, check valve may be faulty or filter clogged.
Replace fuel cap if required.
SPARK PLUG REPLACEMENT
See Figure 21. for RBC430SBS
See Figure 20. for RBC430SES
This engine uses a Champion RY4C or NGK CMR7A
spark plug with 0.6mm electrode gap. Use an exact
replacement and replace annually.
STORING THE PRODUCT
Q
Clean all foreign material from the product. Store
idle unit indoors in a dry, well-ventilated area that is
inaccessible to children. Keep away from corrosive
agents such as garden chemicals.
When storing 1 month or longer:
Q
Drain all fuel from tank into a container approved for
petrol. Run engine until it stops.
