Ryobi RTS1800EF-G - Инструкция по эксплуатации - Страница 4

2

| English

account the working conditions and the work to 
be performed.

 Use of the power tool for operations 

different from those intended could result in a 

KD]DUGRXVVLWXDWLRQ

Ŷ

Keep handles and grasping surfaces dry, clean 
and free from oil and grease.

 Slippery handles and 

grasping surfaces do not allow for safe handling and 

FRQWURORIWKHWRROLQXQH[SHFWHGVLWXDWLRQV

SERVICE

Ŷ

Have your power tool serviced by a qualified repair 
person using only identical replacement parts.

This will ensure that the safety of the power tool is 

PDLQWDLQHG

SAFETY INSTRUCTIONS FOR TABLE SAWS

GUARDING RELATED WARNINGS

Ŷ

Keep guards in place. Guards must be in working 
order and be properly mounted.

 A guard that is 

loose, damaged, or is not functioning correctly must be 

UHSDLUHGRUUHSODFHG

Ŷ

Always use saw blade guard and riving knife for 
every through–cutting operation.

 For through-

cutting operations where the saw blade cuts completely 
through the thickness of the workpiece, the guard and 

RWKHUVDIHW\GHYLFHVKHOSUHGXFHWKHULVNRILQMXU\

Ŷ

Immediately reattach the guarding system after 
completing an operation (such as rebating or 
resawing cuts) which requires removal of the 
guard.

 The guard and riving knife help to reduce the 

ULVNRILQMXU\

Ŷ

Make sure the saw blade is not contacting the 
guard, riving knife or the workpiece before the 
switch is turned on.

 Inadvertent contact of these items 

ZLWKWKHVDZEODGHFRXOGFDXVHDKD]DUGRXVFRQGLWLRQ

Ŷ

Adjust the riving knife as described in this 
instruction manual.

 Incorrect spacing, positioning 

and alignment can make the riving knife ineffective in 

UHGXFLQJWKHOLNHOLKRRGRINLFNEDFN

Ŷ

For the riving knife device to work, it must be 
engaged in the workpiece. 

The riving knife is 

ineffective when cutting workpieces that are too short to 

EHHQJDJHGZLWKWKHULYLQJNQLIH8QGHUWKHVHFRQGLWLRQV
DNLFNEDFNFDQQRWEHSUHYHQWHGE\WKHULYLQJNQLIH

Ŷ

Use the appropriate saw blade for the riving knife. 

For the riving knife to function properly, the saw blade 
diameter must match the appropriate riving knife and 
the body of the saw blade must be thinner than the 
thickness of the riving knife and the cutting width of the 
saw blade must be wider than the thickness of the riving 

NQLIH

CUTTING PROCEDURES WARNINGS

 DANGER

Never place your fingers or hands in the vicinity or 
in line with the saw blade.

 A moment of inattention or 

a slip could direct your hand towards the saw blade and 

UHVXOWLQVHULRXVSHUVRQDOLQMXU\

Ŷ

Feed the workpiece into the saw blade only against 
the direction of rotation.

 Feeding the workpiece in the 

same direction that the saw blade is rotating above the 
table may result in the workpiece, and your hand, being 

SXOOHGLQWRWKHVDZEODGH

Ŷ

Never use the mitre gauge to feed the workpiece 
when ripping and do not use the rip fence as a 
length stop when cross cutting with the mitre 
gauge.

 Guiding the workpiece with the rip fence and the 

mitre gauge at the same time increases the likelihood of 

VDZEODGHELQGLQJDQGNLFNEDFN

Ŷ

When ripping, always apply the workpiece feeding 
force between the fence and the saw blade. Use a 
push stick when the distance between the fence 
and the saw blade is less than 150 mm, and use a 
push block when this distance is less than 50 mm.

“Work helping” devices will keep your hand at a safe 

GLVWDQFHIURPWKHVDZEODGH

Ŷ

Use only the push stick provided by the 
manufacturer or constructed in accordance with 
the instructions.

 This push stick provides sufficient 

GLVWDQFHRIWKHKDQGIURPWKHVDZEODGH

Ŷ

Never use a damaged or cut push stick.

 A damaged 

push stick may break causing your hand to slip into the 

VDZEODGH

Ŷ

Do not perform any operation “freehand”. Always 
use either the rip fence or the mitre gauge to 
position and guide the workpiece.

 “Freehand” means 

using your hands to support or guide the workpiece, in 

OLHX RI D ULS IHQFH RU PLWUH JDXJH )UHHKDQG VDZLQJ
OHDGVWRPLVDOLJQPHQWELQGLQJDQGNLFNEDFN

Ŷ

Never reach around or over a rotating saw blade. 

Reaching for a workpiece may lead to accidental 

FRQWDFWZLWKWKHPRYLQJVDZEODGH

Ŷ

Provide auxiliary workpiece support to the rear 
and/or sides of the saw table for long and/or wide 
workpieces to keep them level.

 $ ORQJ DQGRU ZLGH

workpiece has a tendency to pivot on the table’s edge, 

FDXVLQJORVVRIFRQWUROVDZEODGHELQGLQJDQGNLFNEDFN

Ŷ

Feed workpiece at an even pace. Do not bend or 
twist the workpiece. If jamming occurs, turn the 
product off immediately, unplug the product then 
clear the jam. 

Jamming the saw blade by the workpiece 

FDQFDXVHNLFNEDFNRUVWDOOWKHPRWRU

Ŷ

Do not remove pieces of cut-off material while the 
saw is running.

 The material may become trapped 

between the fence or inside the saw blade guard and 

WKH VDZ EODGH SXOOLQJ \RXU ILQJHUV LQWR WKH VDZ EODGH

Turn the saw off and wait until the saw blade stops 

EHIRUHUHPRYLQJPDWHULDO

Ŷ

Use an auxiliary fence in contact with the table top 
when ripping workpieces less than 2 mm thick.

 A 

thin workpiece may wedge under the rip fence and 

FUHDWHDNLFNEDFN

KICKBACK CAUSES AND RELATED WARNINGS

Kickback is a sudden reaction of the workpiece due to a 

SLQFKHGMDPPHGVDZEODGHRUPLVDOLJQHGOLQHRIFXWLQWKH

workpiece with respect to the saw blade or when a part 
of the workpiece binds between the saw blade and the rip 

IHQFHRURWKHU¿[HGREMHFW0RVWIUHTXHQWO\GXULQJNLFNEDFN