Bosch PCM 8 - Инструкция по эксплуатации - Страница 22

22

 | English 

1 609 92A 1GM | (23.6.15)

Bosch Power Tools

Mounting Individual Components

– Carefully remove all parts included in the delivery from 

their packaging.

– Remove all packaging material from the machine and the 

accessories provided.

– For easier working when mounting the supplied product 

features, please observe that the machine is in the trans-
port position.

Mounting the Tilt-Protector Bar (see figure A)

Before using the power tool for the first time, the tilt-protec-
tor bar 

25

 must be mounted.

– Turn the power tool over and place it carefully on the blade 

guard 

4

 and the saw table 

12

.

– Insert the tilt-protector bar

 25

 into the mounting holes pro-

vided in the base plate until the threaded holes of tilt-pro-
tector bar and base plate are flush.

– Insert the fastening screws 

32

 into the threaded holes and 

tighten them using the hex key

 24

 provided.

– Turn the power tool over so that it is back in the correct po-

sition for working.



Never remove the tilt-protector bar. 

Without the use of 

the tilt-protector bar, the machine does not stand safely 
and can tip over, especially when sawing at maximum mi-
tre/bevel angles.

Mounting to a Working Surface (see figure B)

– Fasten the power tool with suitable screw fasteners to the 

working surface. The mounting holes 

8

 serve for this pur-

pose.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings, some 
wood types, minerals and metal can be harmful to one’s 
health. Touching or breathing-in the dusts can cause allergic 
reactions and/or lead to respiratory infections of the user or 
bystanders.
Certain dusts, such as oak or beech dust, are considered as 
carcinogenic, especially in connection with wood-treatment 
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.

– Always use dust extraction.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-
rials to be worked.

The dust/chip extraction can be blocked by dust, chips or 
workpiece fragments.

– Switch the machine off and pull the mains plug from the 

socket outlet.

– Wait until the saw blade has come to a complete stop.
– Determine the cause of the blockage and correct it.

Integrated Dust Extraction (see figure C)

– Mount  the  dust  bag 

19

 onto the chip ejector 

22

.

During sawing, the dust bag must never come into contact 
with the movable machine parts.

Always empty the dust bag in good time.

External Dust Extraction

For dust extraction, a vacuum hose (size Ø 35 mm) can also 
be connected to the chip ejector 

22

. 

The vacuum cleaner must be suitable for the material being 
worked.
When vacuuming dry dust that is especially detrimental to 
health or carcinogenic, use a special vacuum cleaner.

Changing the Tool (see figures D1 – D4)



Before any work on the machine itself, pull the mains 
plug.



When mounting the saw blade, wear protective gloves. 

Danger of injury when touching the saw blade.

Use only saw blades whose maximum permitted speed is 
higher than the no-load speed of the power tool.
Use only saw blades that correspond with the characteristic 
data given in these operation instructions and that are tested 
and marked in accordance with EN 847-1.
Use only saw blades recommended by the tool manufacturer, 
and suitable for sawing the materials to be cut. This prevents 
overheating of the saw teeth during sawing.

Removing the Saw Blade

– Bring the power tool into the working position.
– Turn  the  hex  socket  screw 

33

 with the hex key 

24

 provided 

and at the same time press the spindle lock 

28

 until it en-

gages.

– Hold the spindle lock 

28

 pressed and unscrew the hex 

socket screw 

33

 in clockwise direction (left-hand thread!).

– Remove the clamping flange 

34

.

– Press lever 

3

 and swing back the retracting blade guard 

5

to the stop.

– Hold the retracting blade guard in this position and remove 

the saw blade 

18

.

– Slowly guide the retracting blade guard downward again.

Mounting the Saw Blade

If required, clean all parts to be mounted prior to assembly.

– Press lever 

3

, swing back the retracting blade guard 

5

 to 

the stop and hold it in this position.

– Place the new saw blade onto the interior clamping flange 

35

.



When mounting the saw blade, pay attention that the 
cutting direction of the teeth (arrow direction on the 
saw blade) corresponds with the direction of the arrow 
on the blade guard!

– Slowly guide the retracting blade guard downward again.
– Place on the clamping flange 

34

 and the screw 

33

.

Press the spindle lock 

28

 until it engages and tighten the 

screw turning in anticlockwise direction.

Operation



Before any work on the machine itself, pull the mains 
plug.

Transport Safety (see figure E)

The transport safety-lock 

26

 enables easier handling of the 

machine when transporting to various working locations.

OBJ_BUCH-2324-002.book  Page 22  Tuesday, June 23, 2015  8:35 AM