Bosch PCM 8 - Инструкция по эксплуатации - Страница 19

 English | 

19

Bosch Power Tools

1 609 92A 1GM | (23.6.15)



Do not reach behind the fence with either hand closer 
than 100 mm from either side of the saw blade, to re-
move wood scraps, or for any other reason while the 
blade is spinning. 

The proximity of the spinning saw blade 

to your hand may not be obvious and you may be seriously 
injured.



Inspect your workpiece before cutting. If the work-
piece is bowed or warped, clamp it with the outside 
bowed face toward the fence. Always make certain that 
there is no gap between the workpiece, fence and table 
along the line of the cut. 

Bent or warped workpieces can 

twist or shift and may cause binding on the spinning saw 
blade while cutting. There should be no nails or foreign ob-
jects in the workpiece.



Do not use the saw until the table is clear of all tools, 
wood scraps, etc., except for the workpiece. 

Small de-

bris or loose pieces of wood or other objects that contact 
the revolving blade can be thrown with high speed.



Cut only one workpiece at a time. 

Stacked multiple work-

pieces cannot be adequately clamped or braced and may 
bind on the blade or shift during cutting.



Ensure the mitre saw is mounted or placed on a level, 
firm work surface before use. 

A level and firm work sur-

face reduces the risk of the mitre saw becoming unstable.



Plan your work. Every time you change the bevel or mi-
tre angle setting, make sure the adjustable fence is set 
correctly to support the workpiece and will not inter-
fere with the blade or the guarding system. 

Without 

turning the tool “ON” and with no workpiece on the table, 
move the saw blade through a complete simulated cut to 
assure there will be no interference or danger of cutting the 
fence.



Provide adequate support such as table extensions, 
saw horses, etc. for a workpiece that is wider or longer 
than the table top. 

Workpieces longer or wider than the 

mitre saw table can tip if not securely supported. If the cut-
off piece or workpiece tips, it can lift the lower guard or be 
thrown by the spinning blade.



Do not use another person as a substitute for a table ex-
tension or as additional support. 

Unstable support for 

the workpiece can cause the blade to bind or the work-
piece to shift during the cutting operation pulling you and 
the helper into the spinning blade.



The cut-off piece must not be jammed or pressed by 
any means against the spinning saw blade. 

If confined, 

i.e. using length stops, the cut-off piece could get wedged 
against the blade and thrown violently.



Always use a clamp or a fixture designed to properly 
support round material such as rods or tubing. 

Rods 

have a tendency to roll while being cut, causing the blade 
to “bite” and pull the work with your hand into the blade.



Let the blade reach full speed before contacting the 
workpiece. 

This will reduce the risk of the workpiece be-

ing thrown.



If the workpiece or blade becomes jammed, turn the 
mitre saw off. Wait for all moving parts to stop and dis-
connect the plug from the power source and/or remove 

the battery pack. Then work to free the jammed mate-
rial. 

Continued sawing with a jammed workpiece could 

cause loss of control or damage to the mitre saw.



After finishing the cut, release the switch, hold the saw 
head down and wait for the blade to stop before remov-
ing the cut-off piece. 

Reaching with your hand near the 

coasting blade is dangerous.



The power tool is provided with a laser warning label 
(marked with number 2 in the representation of the 
power tool on the graphics page).



If the text of the warning label is not in your national 
language, stick the provided warning label in your na-
tional language over it before operating for the first 
time.

Do not direct the laser beam at persons 
or animals and do not stare into the di-
rect or reflected laser beam yourself, not 
even from a distance. 

You could blind 

somebody, cause accidents or damage 
your eyes.



If laser radiation strikes your eye, you must deliberate-
ly close your eyes and immediately turn your head 
away from the beam.



Do not make any modifications to the laser equipment.



Never make warning signs on the machine unrecognis-
able. 



Store the machine in a safe manner when not being 
used. The storage location must be dry and lockable. 

This prevents the machine from storage damage, and from 
being operated by untrained persons.



Never use the machine with a damaged cable. Do not 
touch the damaged cable and pull the mains plug when 
the cable is damaged while working. 

Damaged cables in-

crease the risk of an electric shock.



Check the cable regularly and have a damaged cable re-
paired only through an authorised customer service 
agent for Bosch power tools. Replace damaged exten-
sion cables. 

This will ensure that the safety of the power 

tool is maintained.



Do not use dull, cracked, bent or damaged saw blades. 

Unsharpened or improperly set saw blades produce nar-
row kerf causing excessive friction, blade binding and kick-
back.



Never operate the machine without the insert plate. 
Replace a defective insert plate. 

Without flawless insert 

plates, injuries are possible from the saw blade.



Do not use high speed steel (HSS) saw blades. 

Such saw 

blades can easily break.



Always use blades with correct size and shape (dia-
mond versus round) of arbour holes. 

Blades that do not 

match the mounting hardware of the saw will run eccentri-
cally, causing loss of control.

OBJ_BUCH-2324-002.book  Page 19  Tuesday, June 23, 2015  8:35 AM