Усилители Pioneer A-50 / A-70 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Operation
04
11
En
English
Deutsch
Français
Nederlands
Italiano
Español
Р
ус
ский
Chapter 4:
Operation
Playback
1
Turn on the power of the playback
component.
2
Turn power ON to the unit.
• If the unit is in the standby mode, press the remote
control’s
STANDBY/ON
button.
3
Select the source you want to playback.
Select the playback component.
• When using the front panel controls, rotate the
INPUT SELECTOR
knob.
• In the case of the A-70, if
PHONO
is selected, use
the
CARTRIDGE
select switch to designate the type
of cartridge used with your turntable, either MM
(
) or MC (
).
4
Start playback of the component you
selected in step 1.
5
Adjust playback volume with VOLUME
control.
6
Adjust the tone to your preference using
the BASS and TREBLE controls, and
LOUDNESS button.
If the
DIRECT
button has been set to ON, these controls
are disabled.
3
5
6
6
6
2
MENU
iPod
Music>
Extras>
Settings>
Shuffle Songs
Backlight
/I STANDBY/ON
STANDBY
iPod/USB
5V
2.1A
PURE AUDIO
Hi-Bit 32
FUNCTION
NETWORK AUDIO PLAYER
N-50
SACD/CD player
Network audio player
Turntable
Tuner
iPod dock, etc
CD recorder or
tape deck
Playback
Playback
VOLUME
Set the power to Standby
1
Press the remote control’s
STANDBY/
ON button.
The next time you wish to turn on the power, press the
remote control’s
STANDBY/ON
button.
• If the front panel’s
/I STANDBY/ON
button is
pressed, the power will be turned off. In this case, if
the power is off, pressing the remote control’s
STANDBY/ON
button will not turn on the power.
To turn on the power again, press the front panel’s
/I STANDBY/ON
button.
When using the unit as a power amplifier
When a pre-amplifier is connected to the unit’s
POWER
AMP DIRECT
IN
terminals, the unit can be used as a
power amplifier.
1
Press the POWER AMP DIRECT button
on the front panel of the unit.
The
POWER AMP DIRECT
indicator will light.
Caution
• When the
POWER AMP DIRECT
indicator is
lighted, operations change as follows:
– The unit’s front-panel
VOLUME
,
BASS
,
TREBLE
,
and
BALANCE
controls are disabled. These
adjustments are controlled by the component
connected to the unit’s
POWER AMP DIRECT
IN
terminals.
– The
LOUDNESS
button and
ATTENUATOR
button (A-70 only) are disabled.
– When the
POWER AMP DIRECT
indicator is
lighted, sound volume from the unit will
automatically be fixed at its maximum output.
When using this unit as a power amplifier,
check the output level of the component
connected to the
POWER AMP DIRECT
IN
terminals and set it to a low level as appropriate
before turning on the
POWER AMP DIRECT
indicator. If the sound volume of the component
connected to the
POWER AMP DIRECT
IN
terminals is initially set to a high output level,
loud sound may suddenly be output when the
POWER AMP DIRECT
indicator lights.
– Sound is not produced from the
PHONES
jack
and
RECORDER OUT
terminals.
• For more information, consult the operating
instructions for the component connected to the
unit’s
POWER AMP DIRECT
IN
terminals.
A70_８YXE8.book 11 ページ
年８月
日 火曜日 午後
時
６分
